User manual UNIVERSAL ELECTRONICS MILLENNIUM 4

[. . . ] Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 1 MILLENNIUMTM 4 Universal Remote Control User's Guide Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 2 TABLE OF CONTENTS Introduction . 12 Programming TV/VCR Combo Control . 17 Programming Cable Converter (or DBS Receiver) Control . 30 To Change Volume Lock to the CABLE Mode . [. . . ] Turn on the Cable Converter or DBS Receiver. Press and hold SETUP until the LED blinks twice, then release SETUP. Locate the brand name of your Cable Converter (or Direct Broadcast Satellite Receiver) in the Setup Codes For Cable Converters (or Setup Codes For DBS Receivers) section starting on the next page, and write it in the appropriate space. Cable Converter Brand: ________________ or DBS Receiver Brand: __________________ The brands are listed in alphabetical order with the most popular codes listed first. You will use one of these codes to reprogram the Millennium 4 to operate your Cable Converter or DBS Receiver. Press and hold SETUP until the LED blinks twice, then release SETUP. Enter the first four-digit code for your Cable Converter or DBS Receiver. If you perform this procedure correctly, the LED will blink twice. NOTE: If the LED did not blink twice after entering the code's last digit, then repeat steps 2 through 3 and try entering the same code again. 3. 18 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 19 4. Aim the Millennium 4 at your Cable Converter or DBS Receiver and press POWER once. If it does not respond, repeat steps 2-3, trying each code listed for your brand until you find one that works. If it still does not work , try searching for the code (see Searching For Your Code on page 26). Write your Cable Converter or DBS Receiver code in the boxes below for future reference. 5. NOTE: Remember, to use the Millennium 4 to operate your Cable Converter or DBS Receiver, press CABLE first. To lock the Cable key: 1. Press and hold SETUP until the LED blinks twice, then release SETUP. 3. Setup Codes for Cable Converters: ABC ABC Cable Americast Contec General Instrument GoldStar Hamlin Jerrold Macom Memorex Movie Time NSC Oak Optimus Panasonic Paragon Pioneer Pulsar Quasar RCA Regal Runco 0003, 0008, 0017, 0013 0033 0899 0019 0476, 0276, 0810 0144 0020, 0259 0003, 0012, 0476, 0276, 0810 0033 0000 0063 0063 0019 0021 0000, 0107, 0021 0000 0144, 0533 0000 0000 0021 0020, 0259 0000 continued on next page. . . 19 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 20 Setup Codes for Cable Converters (continued): Samsung Scientific Atlanta Sprucer Starcom TV86 Tocom Toshiba Viewstar Zenith 0144 0008, 0477, 0017, 0277, 0774, 0877 0021 0003 0063 0012, 0013 0000 0063 0000, 0525, 0899 Setup Codes for DBS Receivers: AlphaStar Echostar Expressvu General Instrument HTS Hitachi Hughes JVC Jerrold Magnavox Memorex Next Level Panasonic Philips Primestar RCA Sony Star Choice Toshiba Uniden Zenith 0772 0775 0775 0627, 0361, 0869 0775 0819 0749 0775 0627, 0361 0724, 0722 0724 0869 0701 0724, 0722 0627, 0361 0566 0639 0869 0790 0724, 0722 0856 20 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 21 PROGRAMMING CHANNEL CONTROL LOCK By activating this feature, the Millennium 4 will only allow access to the channel control capabilities of your cable converter. This will guarantee that you do not inadvertently change the channel on your TV or VCR. To Activate Channel Control Lock: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. Now, regardless of what mode you select (i. e. , TV, VCR, or CBL), only the channel control capability of your cable converter will be accessible. NOTE: This feature does not affect the Audio mode. To De-Activate Channel Control Lock: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. The Millennium 4 will again provide TV and VCR channel control capabilities while in the TV or VCR mode. 21 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 22 PROGRAMMING AUDIO CONTROL Using the Millennium 4's Audio mode, you can also control an audio component, such as CD or DVD player, a stereo receiver, a stereo amplifier, or a DBS audio service. Locate the brand name of your audio component in the one of accompanying code lists (starting on the next page). Write it in the appropriate space. CD Player Brand: ____________________________ or DVD Player Brand: ____________________________ or Stereo Receiver Brand: __________________________ or Stereo Amplifier Brand: ________________________ or DBS Audio Brand: ____________________________ The brands are listed in alphabetical order with popular codes listed first. You will use one of these codes to program the Millennium 4 to operate your audio component: 1. Turn on the audio component (or DBS receiver to control its audio service). Press and hold SETUP until the LED blinks twice, then release SETUP. Enter the first four-digit code for your audio component. [. . . ] Now, whenever you press Volume +, Volume ­, or MUTE on the Millennium 4, volume will be controlled by your VCR. 30 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 31 CHANGING VOLUME LOCK To change Volume Lock to the AUDIO mode: NOTE: Performing these steps will allow you to access the volume control of your audio component in all modes. 1. 3. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. Enter 9 - 9 - 3 and then press AUDIO once. Now, whenever you press Volume +, Volume ­, or MUTE on the Millennium 4, volume will be controlled by your audio component. 31 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 32 TROUBLESHOOTING PROBLEM: LED does not blink when you press a key. [. . . ]