User manual UNIVERSAL ELECTRONICS MOSAIC

[. . . ] Mosaic UG rev2 8/30/01 9:07 AM Page 1001 Mosaic UG rev2 8/30/01 9:07 AM Page 1002 MOSAIC INSTALL BATTERIES 1. On Mosaic's back side, push the tab and lift off the battery cover. Obtain four (4) new AA alkaline batteries. Match the + and ­ marks on the batteries to the + and ­ marks in the battery case. [. . . ] Tap on the ADD key to add the device to Mosaic's memory. You will see the default device label being added to the Device Selection Strip. NOTE: If you tap on the REPLACE key instead, Mosaic will ask you to select the device to be replaced and, after your selection, if you want to relabel it. However, if the device to be replaced has programmed keys, Mosaic will first ask if you want to keep or clear the settings. 8. Tap on the OK key to confirm your choice. Mosaic will ask if you want to relabel the newly-added device. · To relabel it, tap on the YES key and you will see the LABEL Menu. Follow the procedure that is similar to the one starting with step 3 on page 54 to relabel the key and tap the OK key when you're done. To keep the label the same, tap on the NO key. continued on next page. . . · Setup By Search 29 Mosaic UG rev2 8/30/01 9:07 AM Page 30 MOSAIC SETUP BY SEARCH (continued) 9. You will see a confirmation screen that says the key has been successfully programmed. To program a function of the same type, tap on the ESC key. To return to the Device Screen, press on ESC or MUTE for at least 2 seconds. To test remote control of the newly-added device, tap on its key on the Device Selection Strip. Try using the Hard Keys to adjust volume and change channels. Try tapping on the Page Arrows to access other remote control functions and then try tapping on the soft keys on each page to test them. 30 Chapter 3: Setting Up Mosaic Mosaic UG rev2 8/30/01 9:07 AM Page 31 USER'S GUIDE SETUP BY CODE Mosaic is a technologically-advanced control device that is designed to be set up using the Set Up By Brand feature described on page 21. This section is reserved for installers and programmers of the Mosaic Touch Screen Control Device who are familiar with setting up devices using manufacturer's 4-digit IR codes. NOTE: Manufacturer's codes are available for customer access on our web site ­ see "About Mosaic" on page 82 for details on locating the URL address. 1. On the Device Screen in the upper left corner, tap on Setup. You will see the main SETUP Menu that greets you and asks, "What would you like to configure?Tap on the DEVICE SETUP key. You will see the DEVICE SETUP Menu. NOTE: To return to a previous menu, tap on the ESC key. To return to last-displayed Device Screen, press down on ESC or MUTE for at least 2 seconds. Tap on the BY CODE key. You will see the CODE SETUP Menu. Esc DEVICE SETUP ?Esc CODE SETUP Select the device. Welcome to Device Setup!What method would you like to use? TV BY BRAND VCR BY SEARCH TUN CBL DVD AMP DAT HOME SAT LD CD PHO Tap on BY CODE TAPE DELETE V. ACC 4. Tap on the device key for the device you want to add (e. g. , VCR). You will see the DEVICE CODE Menu (as shown on the next page) that you will use to enter a working code. NOTE: Make sure the device you want to add is turned off (i. e. , POWER switch is OFF). continued on next page. . . Setup By Code 31 Mosaic UG rev2 8/30/01 9:07 AM Page 32 MOSAIC SETUP BY CODE (continued) Esc CODE SETUP Select the device. Esc CODE SETUP Enter the 4 digit code, press OK to save. OK Device Code TV CBL DVD AMP DAT HOME SAT LD CD PHO _ Tap on VCR TUN TAPE V. ACC 1 4 7 CLEAR 2 5 8 0 3 6 9 5. [. . . ] · To delete all macros, tap on the YES key. You will see a confirmation screen that says all macros have been successfully deleted on all device screens and the main MACROS Menu. Tap on the ESC key to return to the DELETE MACROS Menu. NOTE: Use VIEW/DELETE (see "Chapter 4: Personalizing Mosaic ­ Using View/Delete" on page 65) to delete macros from Device Screens but keep them intact on the main MACROS Menu for future copying. · To cancel deletion of all macros, tap on the NO key. Mosaic will return to the main MACROS Screen. If you want to delete a single macro, see the previous section, Deleting A Macro on page 45, or see Using View/Delete on page 65. NOTE: To return to a previous menu, tap on the ESC key. [. . . ]