User manual UNIVERSAL ELECTRONICS NEVO

[. . . ] Then insert the new batteries, as shown on right. Align the cover's keys with the opening's holes and press the cover back into place. QUICK START 4. You will see the Mosaic Welcome screen, followed by the Device screen. USING THE TOUCH SCREEN Mosaic features a Touch Screen that responds to touch commands, whether you use the supplied Stylus or your finger tip. Each time you tap on the screen, you'll see the LED blink and hear a beep tone, which serve as visual and audio confirmation of your command. [. . . ] What method would you like to use? TV BY BRAND VCR CBL DVD AMP DAT HOME SAT LD CD PHO Tap on BY SEARCH TUN BY CODE TAPE DELETE V. ACC 4. Tap on the device key for the device you want to add (e. g. , VCR). You will see the SEARCH Test Menu (as shown on the next page) that you will use to find a working code. NOTE: Make sure the device you want to add is turned off (i. e. , POWER switch is OFF). continued on next page. . . Setup By Search 27 Mosaic UG rev2 8/30/01 9:07 AM Page 28 NEVO SETUP BY SEARCH (continued) Esc SEARCH Select the device. Esc SEARCH OK Use the test keys to find your device type. Press OK to save. PREV TV CBL DVD AMP DAT HOME SAT LD CD PHO VCR Test NEXT Tap on VCR TUN TAPE V. ACC PWR 1 5. Aim Mosaic at the desired device (e. g. , VCR) and tap on the PWR key. If it does not respond, advance the code test by tapping on the NEXT key and then tap on the PWR key again. If the device still does not respond, repeat this process, advancing through code tests until you find a code that works. Esc SEARCH OK To check previous code, tap on Use the test keys to find your device type. Press OK to save. PREV VCR Test NEXT If device does not respond, tap and repeat test. First, tap on PWR 1 28 Chapter 3: Setting Up Mosaic Mosaic UG rev2 8/30/01 9:07 AM Page 29 USER'S GUIDE 6. To save a code that works, tap on the OK key. You will see the SEARCH ADD/REPLACE menu that lists two choices. Tap on Esc SEARCH OK Esc SEARCH ? Use the test keys to find your device type. Press OK to save. Would you like to ADD the device or REPLACE it with an existing one? PREV VCR Test NEXT PWR ADD REPLACE 1 · Use the ADD key when setting up a new device (e. g. , a DVD player) that is not currently on the Device Selection Strip (if needed, refer to Using the Touch Screen ­ Selecting a Device on page 18). The remaining instructions assume you will be adding a new device. continued on next page. . . Setup By Code 31 Mosaic UG rev2 8/30/01 9:07 AM Page 32 NEVO SETUP BY CODE (continued) Esc CODE SETUP Select the device. Esc CODE SETUP Enter the 4 digit code, press OK to save. OK Device Code TV CBL DVD AMP DAT HOME SAT LD CD PHO _ Tap on VCR TUN TAPE V. ACC 1 4 7 CLEAR 2 5 8 0 3 6 9 5. Using the keypad, tap in a four-digit code and then tap the OK key. If the code is valid, you will see the CODE SETUP ADD/REPLACE menu that lists two choices. NOTE: If the code is not valid, Mosaic will reject it and prompt you to try again. If you make a mistake entering the code, tap the CLEAR key to erase it. Then tap on Esc CODE SETUP Enter the 4 digit code, press OK to save. OK Esc CODE SETUP ? Would you like to ADD the device or REPLACE it with an existing one? Device Code First, enter code. 1234 1 4 7 CLEAR 2 5 8 0 3 6 9 ADD REPLACE 32 Chapter 3: Setting Up Mosaic Mosaic UG rev2 8/30/01 9:07 AM Page 33 USER'S GUIDE · Use the ADD key when setting up a new device (e. g. , a DVD player) that is not currently on the Device Selection Strip (if needed, refer to Using the Touch Screen ­ Selecting a Device on page 18). The remaining instructions assume you will be adding a new device. Use the REPLACE key to replace a device (e. g. , a new TV set) that is currently on the Device Selection Strip. · 6. Tap on the ADD key to add the device to Mosaic's memory. You will see the default device label being added to the Device Selection Strip. NOTE: If you tap on the REPLACE key instead, Mosaic will ask you to select the device to be replaced and, after your selection, if you want to relabel it. However, if the device to be replaced has programmed keys, Mosaic will first ask if you want to keep or clear the settings. 7. Tap on the OK key to confirm your choice. Mosaic will ask if you want to relabel the newly-added device. · To relabel it, tap on the YES key and you will see the LABEL Menu. [. . . ] Tap on the PERSONALIZATION key. You will see the PERSONALIZATION Menu. NOTE: To return to a previous menu, tap on the ESC key. To return to last-displayed Device Screen, press down on ESC or MUTE for at least 2 seconds. Tap on the MACROS key. You will see the main MACROS Menu. Mosaic will ask you to confirm your choice (as shown on the next page). [. . . ]