User manual UNIVERSAL REMOTE CONTROL ATLAS OCAP 5-DEVICE

[. . . ] Atlas OCAP M1056L. fm Page 1 Friday, December 22, 2006 6:10 PM ATLAS OCAP 5-Device Remote Control with Learning Users Guide PREPROGRAMMED FOR YOUR SET-TOP BOX Atlas OCAP M1056L. fm Page 2 Friday, December 22, 2006 6:10 PM TABLE OF CONTENTS Introduction . 16 Deleting All Learned Keys in a Specific Mode . 18 Unlocking Volume Control for a Single Device (Individual Volume Unlock) . 18 Unlocking All Volume Control (Global Volume Unlock) . [. . . ] Repeat steps 2 through 5 for another mode and/or key or press and hold SETUP to exit programming. Deleting a Single Learning Key This process returns the key to its original programming for the mode you select. You can also delete learned programming by teaching a different function to the key (see "Programming a Learned Key" on page 15) NOTE: If more than 15 seconds pass between key presses, the remote exits programming. Press and hold SETUP until the last-selected mode key blinks twice, then press 9 7 6. 2. Press a mode key once (i. e. , VCR, DVD, AUD, TV, or CBL). Press the key containing the learned function to be deleted twice. Repeat steps 2 through 3 for another key or press and hold SETUP to exit programming. 3. 4. www. urcsupport. com/atlasocap 16 Atlas OCAP M1056L. fm Page 17 Friday, December 22, 2006 6:10 PM Deleting All Learned Keys in a Specific Mode NOTE: If more than 15 seconds pass between key presses, the remote exits programming. Press and hold SETUP until the last-selected mode key blinks twice, then press 9 7 5. 2. 3. Press a mode key twice (i. e. , VCR, DVD, AUD, TV, or CBL) to clear all the learned keys for that mode. Repeat step 2 for another mode or press and hold SETUP to exit programming. PROGRAMMING CHANNEL CONTROL LOCK By default, the remote control's channel-control capabilities are locked to the cable converter. The affected keys* are 1 through 0, CH+, CH-, and LAST. This will guarantee that you do not inadvertently change a channel on your TV or VCR. However, you can deactivate this feature to allow full access to these keys in the TV and VCR modes. *NOTE: This feature does not affect the AUD mode. On the remote control, press CBL once; it will blink once. Press and hold SETUP until the CBL key blinks twice. The CBL key will blink twice. 3. Press CH- once. The CBL key will blink four times. Now the remote control will provide TV and VCR channel-control capabilities while in the TV or VCR mode. www. urcsupport. com/atlasocap 17 Atlas OCAP M1056L. fm Page 18 Friday, December 22, 2006 6:10 PM Locking Channel Control to CBL 1. On the remote control, press CBL once; it will blink once. Press and hold SETUP until the CBL key blinks twice. Enter 9 7 3. The CBL key will blink twice. 3. Press CH+ once. The CBL key will blink twice. Now, regardless of what mode you select (except AUD), the channel keys will only change channels on your cable converter. CHANGING VOLUME LOCK Volume Lock allows you to control the volume through the device identified as having your primary speaker(s), regardless of which mode you are using. On the Atlas OCAP 5-Device Remote Control with Learning, Global Volume Lock is set to TV, so you can control TV volume while in the VCR, DVD, TV or CBL mode. [. . . ] SOLUTION: Re-program the CBL key for cable code 0476 (see "Programming Device Control" on page 10). PROBLEM: Tried Search Method and still could not find a working code. SOLUTION: Try the Search Method again after clearing out the device key as follows: a. Press and hold SETUP until device key blinks twice. [. . . ]