User manual UNIVERSAL REMOTE CONTROL AVEX R6

[. . . ] Congratulations! Congratulations on purchasing Universal Remote Control's AVEXTM R6 Pre--Programmed and Learning remote control. You now have the power to control your entire home entertainment system with one easy--to--use remote. The AVEX R6 can be used with thousands of audio/video components because of the extensive library of codes that have already been programmed into the remote. get ready to sit back, relax, and simplify your home entertainment experience. [. . . ] The component LED light will blink three times to confirm the programming. Now test all the buttons to make sure they learned correctly. Repeat Steps 1-5 to program any other component modes. If the Learning Method does not work, here are a few suggestions: · If you have a Plasma TV, move to another room · Avoid programming under fluorescent light or direct sunlight · Put new batteries in the old remote · Gradually vary the distance between the two remote controls · Tap the button on your old remote instead of pressing and holding it during the learning process Here are some additional facts regarding the Learning process: · Learned functions override any existing pre-programmed functions on the remote control · Learned functions are automatically erased when a new function is learned on the same button · Learned functions are retained even after a different set-up code number is programmed into the remote control · To return to an original pre-programmed function, a learned function must to be erased Page 15 AUX Function: Programming a 6th Component After you've finished programming the AVEX R6 for five primary components and you did not use AUX, you can take advantage of the AUX function to program a 6th component, such as a second TV, DVD, or any other audio/video component that you may have in your system. Finding a Component's Set-up Code Number If you used the Auto--Search or Learning Methods to program a component, you may not know the code number you programmed. Here is a way for you to identify what that code number is, so you can make a note in the back of this Manual for future reference. STEP 1: Press the component button you would like to verify and the SELECT [SEL] button at the same time for 2 seconds until the selected component LED light turns on. IMPORTANT: You have 30 seconds to perform the next step while you are in programming mode. If you do not press a button within 30 seconds, the component LED light will turn off. The remote will exit the programming mode and you will have to start over. COMPONENT BUTTONS SELECT INFO STEP 2: Press the INFO button and count the number of times the Component LED light blinks. This number indicates the first digit of the code. Next it will pause for about one second and begin blinking again to indicate the number of the second digit. Then once again it will pause, then blink, o indicate the number of the third digit. Example: One blink, pause, eight blinks, pause, three blinks indicates code number 183. Note that ten (10) blinks represent the number 0. Page 16 Programming Special Advanced Features Programming Multi-Commands to Macro Buttons The AVEX R6 has six Macro buttons (POWER, SYSTEM OFF, A, B, C, D) that are designed to store up to 20 commands in each button. Pressing any one of the Macro buttons will send out the series of commands that are stored in that particular button. MacroPowerTM Total System On/Off MacroPower makes several devices work together by pressing one button. Imagine the convenience of turning on your TV, your DVD player and your Surround Sound receiver by pressing a single button on your AVEX R6. What could normally take three remotes and three button pushes, the AVEX R6 can accomplish with the press of one button. Any of the Power On or the System Off buttons can be programmed for MacroPower control. To set it up, follow these easy steps: STEP 1: To program MacroPower commands for the Power ON button, press the POWER button and the MUTE button at the same time for 2 seconds until one of the component button LED lights turns on. POWER MUTE Page 17 IMPORTANT: You have 30 seconds to perform the next step while you are in programming mode. If you do not press a button within 30 seconds, the component LED light will turn off. [. . . ] Press and hold both the TV and RECORD buttons for about five seconds until the SAT/CABLE component LED light blinks five times. All programming and setup codes that you have entered into the remote will be erased and the AVEX R6 will return to the original factory default settings. Warning This procedure will erase all programming and set-up codes that you have entered into the remote. SAT/CABLE TV COMPONENT BUTTON RECORD Page 30 Pre-Programmed Code Tables The AVEX R6 Pre-Programmed code library is classified by category (TV, VCR, DVD, etc. ). Within each category, the code numbers are listed in rows by brand (Sony, Panasonic, B & K, etc. ). [. . . ]