User manual UNIVERSAL REMOTE CONTROL MILLENNIUM 4

[. . . ] Millennium 4 Mnl M4094 rev 12/27/02 11:00 AM Page 1 MILLENNIUMTM 4 Universal Remote Control User's Guide Millennium 4 Mnl M4094 rev 12/27/02 11:00 AM Page 2 TABLE OF CONTENTS Introduction . 17 Programming Cable Converter (or DBS Receiver) Control . 28 To Change Volume Lock to the Cable Mode . 28 To Change Volume Lock to the TV Mode. [. . . ] However, if you have another brand or model of cable converter or satellite receiver that you would like to control, then you'll need to perform the following instructions to unlock the cable key, enter in a new code, and lock the cable key again. To Unlock the CBL Key: 1. Turn on the Cable Converter or DBS Receiver. Press and hold SETUP until the LED blinks twice, then release SETUP. 4. 18 Millennium 4 Mnl M4094 rev 12/27/02 11:00 AM Page 19 To Program the CBL Key: 1. On the next page, locate the brand name of your Cable Converter in Setup Codes For Cable Converters, or DBS (Direct Broadcast Satellite) Receiver in Setup Codes For DBS Receivers, and write it in the appropriate space below. Cable Converter Brand: ________________ or DBS Receiver Brand: __________________ The brands are listed in alphabetical order with the most popular codes listed first. You will use one of these codes to reprogram the Millennium 4 to operate your Cable Converter or DBS Receiver. Press and hold SETUP until the LED blinks twice, then release SETUP. Enter the first four-digit code for your Cable Converter or DBS Receiver. If you perform this procedure correctly, the LED will blink twice. NOTE: If the LED did not blink twice after entering the code's last digit, then repeat steps 2 through 3 and try entering the same code again. 3. 4. Aim the Millennium 4 at your Cable Converter or DBS Receiver and press POWER once. If it does not respond, repeat steps 2-3, trying each code listed for your brand until you find one that works. If it still does not work , try searching for the code (see Searching For Your Code on page 24). Write your Cable Converter or DBS Receiver code in the boxes below for future reference. 5. NOTE: Remember, to use the Millennium 4 to operate your Cable Converter or DBS Receiver, press CBL first. continued on next page. . . 19 Millennium 4 Mnl M4094 rev 12/27/02 11:00 AM Page 20 PROGRAMMING CABLE CONVERTER (OR DBS RECEIVER) CONTROL (continued) To Lock the CBL Key: 1. Press and hold SETUP until the LED blinks twice, then release SETUP. 3. Setup Codes for Cable Converters: ABC Americast Bell South General Instrument GoldStar Hamlin Jerrold Memorex Panasonic Paragon Philips Pioneer Pioneer Pulsar Quasar Regal Runco Samsung Scientific Atlanta Starcom Toshiba Zenith 0003, 0008 0899 0899 0476 0144 0273 0003, 0476 0000 0000 0000 0305 0144, 0877, 0533 0533 0000 0000 0273 0000 0144 0008, 0477, 0877 0003 0000 0525, 0000, 0899 Setup Codes for DBS Receivers: Echostar 0775, 1005 Expressvu 0775 GE 0566 General Instrument 0869, 0892 HTS 0775 Hughes Network Sys. 0749 JVC 0775 Mitsubishi 0749 20 Millennium 4 Mnl M4094 rev 12/27/02 11:00 AM Page 21 Next Level Philips Proscan RCA RadioShack Samsung Sony Star Choice Toshiba 0869, 0892 0749, 1076 0392 0566, 0392 0869 1109 0639 0869 0749 PROGRAMMING CHANNEL CONTROL LOCK By activating this feature, the Millennium 4 will only allow access to the channel control capabilities of your cable converter. This will guarantee that you do not inadvertently change the channel on your TV or VCR. To Activate Channel Control Lock: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. Now, regardless of what mode you select (i. e. , TV, VCR, or CBL), only the channel control capability of your cable converter will be accessible. NOTE: This feature does not affect the Audio mode. To De-Activate Channel Control Lock: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. The Millennium 4 will again provide TV and VCR channel control capabilities while in the TV or VCR mode. 21 Millennium 4 Mnl M4094 rev 12/27/02 11:00 AM Page 22 PROGRAMMING AUDIO CONTROL Locate the brand name of your audio amplifier or receiver in the one of accompanying code lists at the end of this section. Write it in the appropriate space below. Audio Amplifier Brand: ________________________ or Audio Receiver Brand:__________________________ The brands are listed in alphabetical order with popular codes listed first. You will use one of these codes to program the Millennium 4 to operate your audio device: 1. Press and hold SETUP until the LED blinks twice, then release SETUP. [. . . ] Now, whenever you press press VOL+, VOL-, or MUTE on the Millennium 4, volume will be controlled by your VCR or DVD player. 28 Millennium 4 Mnl M4094 rev 12/27/02 11:00 AM Page 29 To Change Volume Lock to the Audio Mode: NOTE: Performing these steps will allow you to access the volume control of your audio component in all modes. 1. 3. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. Enter 9 - 9 - 3 and then press AUDIO once. Now, whenever you press press VOL+, VOL-, or MUTE on the Millennium 4, volume will be controlled by your audio component. 29 Millennium 4 Mnl M4094 rev 12/27/02 11:00 AM Page 30 TROUBLESHOOTING PROBLEM: LED does not blink when you press a key. [. . . ]