User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL 8811 WO CODE

[. . . ] Press MUTE once to turn the sound off or on. In TV, VCR, DVD, SAT, and CBL modes, use FAV to scan favorite channels and/or all channels. See Using Channel Scan and Programming Favorite Channel Scan. Use CH+ (or CH-) to select the next higher (or lower) channel. 3. [. . . ] The store, at its option, will replace or repair this product if found to be defective. Press and hold SET until the LED (red light) blinks twice, then release SET. Use the Setup Codes For TV/VCR Combos (on the back) to locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering the same code again. ABOUT UPGRADING The One For All 8L Home Theater Upgradeable Universal Remote Control with Learning has the largest infrared code library available. However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes stored in the remote control's memory. If this happens, please contact our Customer Support department (see Customer Support below) to upgrade the remote control. The Customer Support representative will search our entire database for a code that matches your device and instruct you how to enter it into your One For All 8L Home Theater Upgradeable Universal Remote Control with Learning. If the code for your home entertainment or home automation device is not in our database, we will need to "capture" the code for that device from its original remote control. A new code would then be created and entered into your One For All 8L Home Theater Upgradeable Universal Remote Control with Learning. If necessary, the Customer Support representative can instruct you how to begin the capture procedure. NOTE: One For All reserves the right to replace a returned remote control with a new one of equal or superior functionality. The default Device Group setting from the factory is: 5. Then enter the following sequence: CBL, POWER, and 1-1 (or 0 -1- 1 if access is over 100 channels) 6. Press and hold SET until the LED blinks twice, then release SET. Now when you press M2 once, the TV will turn on and tune to channel 03. Then the cable box will turn on and tune to channel 11. To Re-Assign Device Key AUX as 2nd TV key: AUX as 2nd DVD key: AUX as 2nd SAT key: AUX as 2nd CD key: AUX as 2nd CBL key: AUX as 2nd RCVR/AMP key: Perform Sequence SET - 9 - 9 - 2 - TV - AUX SET - 9 - 9 - 2 -DVD- AUX SET - 9 - 9 - 2 -SAT- AUX SET - 9 - 9 - 2 -CD- AUX SET - 9 - 9 - 2 -CBL- AUX SET - 9 - 9 - 2 - RCVR/AMP - AUX Clearing A Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Select a macro key (e. g. , M1~M4) you want to clear and press it once. Press and hold SET until the LED blinks twice, then release SET. FEATURES AND FUNCTIONS Use the Key Charts (below) to learn how to use the universal features and functions of the One For All 8L Home Theater Upgradeable Universal Remote Control with Learning (URC-8811). 5. Aim the remote control at the device and press POWER once. If the device does not respond, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (Play) key. Programming The Home Theater Mode For example, let's assume you have a TV, a cable box, and a VCR in your home theater system. You can set up the Home Theater mode so that selected controls are assigned to these devices as follows: 1. On the remote control, press HOME THEATER. Press and hold SET until the LED (red light) blinks twice, then release SET. [. . . ] On the remote control, press TV, VCR, DVD, SAT, or CBL once. Press and hold SET until the LED (red light) blinks twice, then release SET. Use the keypad to enter a favorite channel number (e. g. , 031). Then press SET once. NOTE: If the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e. g. , 0 -3-1-Enter). SOLUTION: 1. [. . . ]