User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL URC4110

[. . . ] Press SLEEP to activate your device's sleep timer (not available for all devices). Use TV/VID to switch the TV's input to view TV or video program. Use the keypad (0 ~ 9) to directly select channels (for example, 09 or 31). Press ENTER once after entering channel numbers on some TV models. Press PREV CH once to recall the last-viewed channel and to page back one screen on the main menu. [. . . ] Press and hold SET until the LED blinks twice, then release SET. 5. Your One For All 4 Devices is now programmed to operate your TV/DVD. Write your TV/DVD code for future reference. Remember, if you want to use your One For All 4 Devices to operate your TV/DVD, press the DVD key first. 3. Use the Manufacturer's Codes (starting on page 12) to locate the type of device and brand name and then enter the first four-digit code for your component. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. 5 6 CTGRD4N 4110 manual booklet. QXD 5/2/06 3:09 PM Page 7 SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV: 1. Press and hold SET until the LED blinks twice, then release SET. 4. The DVD key is now ready to be programmed for your second TV. (See Setting up your components. ) To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular components: To Re-Assign Key VCR as 2nd TV key: VCR as 2nd CBL key: VCR as 2nd SAT key: VCR as 2nd DVD key: VCR back to VCR: DVD as 2nd TV key: DVD as 2nd CBL key: DVD as 2nd SAT key: DVD as 2nd VCR key: DVD back to DVD: Sequence Perform SET - 9 - 9 - 2 - TV - VCR SET - 9 - 9 - 2 - CBL/SAT - VCR SET - 9 - 9 - 2 - CBL/SAT - VCR SET - 9 - 9 - 2 - DVD - VCR SET - 9 - 9 - 2 - VCR - VCR SET - 9 - 9 - 2 - TV - DVD SET - 9 - 9 - 2 - CBL/SAT - DVD SET - 9 - 9 - 2 - CBL/SAT - DVD SET - 9 - 9 - 2 - VCR - DVD SET - 9 - 9 - 2 - DVD - DVD Enter 9 - 9 - 1. Aim the remote control at the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off. NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. 5. To lock in the code, press and hold SET until the LED blinks twice, then release SET. 6. To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for. CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment: For example, to find out which code is operating your TV: 1. Press and hold SET until the LED blinks twice, then release SET. When a re-assignment is done, the LED will blink twice to confirm your choice. At that time, you will need to program the remote control for the new device (see Setting up your components). CHANGING VOLUME LOCK The One For All 4 Devices is set to control the volume of your TV in the TV, VCR, CBL/SAT, and DVD modes. If you want the volume to be controlled by a mode other than TV (e. g. , CBL/SAT), change the Volume Lock as follows: To Change Volume Lock To Another Mode: 1. On the remote control, press and hold SET until the LED blinks twice, then release SET. Enter 9 - 9 - 3 and then press any mode key once (except TV). Now, whenever you press VOL+, VOL­, or MUTE, volume will be controlled by your mode choice. Enter 9 - 9 - 0. Replace batteries with four new AAA alkaline batteries. LED blinks when you press a key, but home entertainment component does not respond. Make sure the remote control is aimed at your home entertainment device and is not farther than 15 feet away. The unit does not control home entertainment devices or commands are not working properly. Try all listed codes for thecomponent brands being set up. [. . . ] URC-8811 One For All A/V LCD 8 Device With Learning . URC-8910 One For All IR/RF LCD 8 Device With Learning . URC-9910 One For All 8 Device Home Theater Remote Powered By Kameleon . URC-9960 MANUFACTURER'S CODES Setup Codes for Cable Boxes ABC Americast Bell South Digeo Jerrold Memorex Motorola Pace Panasonic Paragon 0003, 0008 0899 0899 1187 0003, 0276 0000 0276, 1187, 1376 0008, 1877 0000 0000 Pioneer Pulsar Quasar Runco Scientific Atlanta Starcom Supercable Torx Toshiba Zenith 0533, 1877 0000 0000 0000 0008, 1877 0003 0276 0003 0000 0000, 0899 General Instrument 0003, 0276 Setup Codes for Cable Box/PVR (or DVR) Combos Americast Digeo Motorola Pace 0899 1187 1376, 1187 1877 Pioneer Scientific Atlanta Zenith 1877 1877 0899 Setup Codes for Satellite Receivers DirecTV 1377, 0099, 0247, 0392, 0566, 0639, 0724, 0749, 0819, 1076, 1108, 1142, 1392, 1442, 1609, 1639, 1640, 1749, 1856 0775 Motorola Next Level Panasonic Paysat Philips Dish Network System 0775, 1005, 1505, 1775 Dishpro Echostar Expressvu GE GOI Hisense Hitachi HTS Hughes Hughes Network Systems iLo Jerrold JVC Magnavox Memorex Mitsubishi 0775, 1005, 1505, 1775 0775, 1005, 1505, 1775 0775, 1775 0392, 0566 0775, 1775 1535 0819 0775, 1775 0749, 1442, 1749 0749, 1142, 1442, 1749 1535 0869 0775, 1775 0724 0724 0749 Pioneer Proscan Proton RadioShack RCA Samsung Sony Star Choice Tivo Toshiba UltimateTV Uniden US Digital USDTV Voom Zenith 0856, 0869 0869 0247, 0701 0724 0099, 0724, 0749, 0819, 1076, 1142, 1442, 1749 442 0392, 0566 1535 0869 0392, 0566, 0855, 1392 1108, 1142, 1276, 1377, 1442, 1609 0639, 1639, 1640 0869 1142, 1442 0749, 0790, 0819, 1285, 1749 1392, 1640 0724 1535 1535 0869 1856 Dish Network ONE FOR ALL® is the registered trademark of Universal Electronics Inc. [. . . ]