User manual UNIVERSAL REMOTE CONTROL RF10

[. . . ] 1 The RF10 Remote Congratulations! Congratulations on purchasing Universal Remote Control's MASTERCONTROLTM RF10 Pre-programmed and Learning Remote Control!You now have the power to control your entire home entertainment system with one easy-to-use remote. The RF10 can be used with thousands of audio/video Components because of the extensive code library pre-programmed into the remote. And, the RF10's impressive lineup of special advanced features can automate and customize the operation of your system in many ways. [. . . ] Some brands have several possible code numbers. ADVANCED SETUP Channel buttons (for TV), or PLAY and STOP (for VCR and DVD) to make sure they all work. If any of the buttons do not work properly, you need to find a new correct code. For example, maybe your Sony TV turned off with code number 147, but the volume controls did not work properly. If this is the case, try the next code number listed for that Component until you find a perfect match. ADVANCED SETUP STEP 6: Once you have found the right code, save the code number by pressing the Component button you pressed in STEP 2 (in this case AUX) one more time. The LCD screen will blink "SAVED" two times, signaling that the code number has been successfully saved, and then return to normal operating mode. NOTE: Any component button can be setup to operate any type of component by following these same steps. Simply substitute the desired component button in place of AUX in STEP 2. STEP 5: IMPORTANT: You now have 30 seconds to perform the next step while you are in Setup mode. If you don't press a button within 30 seconds, "SET" will disappear from the screen, signaling that you have exited Setup mode and you will need to start over. When the Component turns off, press the ON button to turn the Component back on. Now you can test the Volume and AUX BUTTON NUMBER BUTTONS 25 Recalling Pre-Programmed Setup Code Numbers 26 Recalling Pre-Programmed Setup Code Numbers In case you didn't write down the Pre-Programmed Code Numbers that you used to setup your RF10, you can easily recall them using this simple process: STEP 1: Press and hold both the COMPONENT you want to identify and the SEL (Select) buttons at the same time for approximately 3 seconds, until the word "SET" is displayed on the LCD screen. This signals that you are now in setup mode. STEP 2: Press the INFO button. The name of the selected component will blink twice on the LCD screen, followed by the 3-digit code. Write down the code numbers as they appear for future reference. Pages 37 of this manual provides a convenient space for you to record your code numbers. ADVANCED SETUP ADVANCED SETUP IMPORTANT:You now have 30 seconds to perform the next step while you are in SETUP mode. If you don't press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. The RF10 will then automatically return to normal operating mode. 27 Erasing Commands - Overview 28 Erasing Commands ­ Overview You can erase a single command, all learned commands in each component mode, SimpleSoundTM commands or MacroPowerTM commands. If you really want a fresh start, it is possible to reset the RF10 to its original factory default settings. Erasing Commands Erasing One Learned Command STEP 1: Press and hold both the COMPONENT button where the command is stored and the ENT (Enter) button at the same time for approximately 3 seconds, until the word "LEARN" is displayed on the LCD screen. IMPORTANT:You now have 30 seconds to perform the next step while you are in LEARN mode. If you don't press a button within 30 seconds, LEARN will disappear from the screen, signaling that you have exited erase mode and you will need to start over. STEP 2: Press and hold the button you want to erase for 2 seconds. The display will flash ERASE twice, then display LEARN. ERASING COMMANDS ERASING COMMANDS Repeat this step to erase any other buttons in the same mode. COMPONENT COMPONENT BUTTONS BUTTON ENT ENT BUTTON BUTTONS STEP 3: To save, press and hold the COMPONENT button and the ENT button until the word "SAVED" flashes twice on the LCD screen. The RF10 will then automatically return to normal operating mode. 29 Erasing Commands 30 Erasing Commands Erasing All Learned Commands in One Component STEP 1: Press and hold both the COMPONENT button where the command is stored and the ENT (Enter) button at the same time for approximately 3 seconds, until the word "LEARN" is displayed on the LCD screen. IMPORTANT:You now have 30 seconds to perform the next step while you are in LEARN mode. If you don't press a button within 30 seconds, LEARN will disappear from the screen, signaling that you have exited erase mode and you will need to start over. STEP 2: Press and hold both the COMPONENT button you want to erase and the PAUSE button until the display flashes ERASE eight times, followed by SAVED. Release the buttons and the RF10 will then automatically return to normal operating mode. ERASING COMMANDS ERASING COMMANDS COMPONENT BUTTONS ENT BUTTON COMPONENT BUTTONS PAUSE BUTTON 31 Erasing Commands 32 Erasing Commands Erasing All Learned Commands in ALL Components Erasing Macro Commands STEP 1: Press and hold both the POWER ON and the STOP buttons for 10 seconds, until the display flashes ERASE ten times STEP 1: Press and hold one of the MACRO buttons (ON, OFF or one of the 8 COMPONENT buttons) and the MUTE button, until the word "MACRO" is displayed on the LCD screen. IMPORTANT: You now have 30 seconds to perform the next step while you are in MACRO mode. If you don't press a button within 30 seconds, MACRO will disappear from the screen, signaling that you have exited erase mode and you will need to start over. ERASING COMMANDS STEP 2: Release the buttons and the display will flash SAVED twice and the RF10 will automatically return to normal operating mode ERASING COMMANDS POWER ON BUTTON STOP BUTTON STEP 2: Press the CHANNEL ( ) UP button to save. The display will flash CLEAR and then SAVED two times. MACRO BUTTONS 33 Re-setting RF10 to Original Factory Default Settings 34 Re-setting RF10 to Original Factory Default Settings If you want to start with a clean slate, you can re-set the RF10 its original factory default settings by performing the following steps. NOTE: This process will essentially erase EVERYTHING you have programmed into the RF10. STEP 1: Press and hold both the POWER OFF button and the STOP button for 10 seconds. Continue to hold both buttons as the display flashes ERASE ten times, then RESET. ERASING COMMANDS ERASING COMMANDS The RF10 will then display a self-testing routine for a few seconds, then automatically return to normal operating mode. POWER OFF BUTTON STOP BUTTON 35 The Optional PowerBlasterTM 36 The Optional PowerBlasterTM (for `barrier-free' RF control) [Sold separately] Of all the fabulous RF10 features, this is probably the most exciting. [. . . ] Press SHIFT first, then press REAR+ button. Press SHIFT first, then press MODE- button. Press SHIFT first, then press SUB- button. Press SHIFT first, then press CENTER- button. [. . . ]