User manual UNIVERSAL REMOTE CONTROL RF20

[. . . ] 1 The RF20 Remote Congratulations! Congratulations on purchasing Universal Remote Control's MASTERCONTROLTM RF20 Pre-programmed and Learning Remote Control!You now have the power to control your entire home entertainment system with one easy-to-use remote. The RF20 can be used with thousands of audio/video Components because of the extensive code library pre-programmed into the remote. And, the RF20's impressive lineup of special advanced features can automate and customize the operation of your system in many ways. [. . . ] A new screen appears displaying SAVE, UNDO or EXIT. MacroPowerTM Setup STEP 9: When you are finished setting up Favorite Channel buttons, press the MAIN button twice to return to normal operation. STEP 1: Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word "SETUP" is displayed at the top of the LCD touch screen. This signals that you are now in setup mode. IMPORTANT: You now have 30 seconds to perform the next step while you are in SETUP mode. If you don't press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. STEP 4: Press the first component display button you want the Macro to turn on (in this example, TV) and "TV" will display at the top of the screen and "STEP 1" at the bottom. STEP 8: To save the channel you entered, press the SAVE display button. The UNDO display button lets you erase the last entry. The EXIT display button erases all entries for this button. STEP 5: Then, press the ON button to confirm the command and "STEP 2" will display at the bottom of the screen. (NOTE: Whenever a button is pressed, another Macro step is counted and displayed at the bottom of the screen. ) STEP 2: CUSTOMIZING SAVE BUTTON Press the MACRO display button on the LCD screen. The top of the screen will display "MACRO". The bottom of the display will flash "SELECT". CUSTOMIZING STEP 6: Now, press the MAIN button to return to the Main Component listing. ("STEP 3" will display at the bottom of the screen. ) STEP 3: Press the ON button. "ON" will display at the top of the LCD screen. "STEP0" will display at the bottom of the screen indicating that no macro steps have been entered yet. 27 MacroPowerTM Setup 28 MacroPowerTM Setup STEP 7: Press the second component display button that you want the Macro to turn on (in this example, VCR) and "VCR" will display at the top of the screen. ("STEP 4" will display at the bottom of the screen. ) STEP 11: Then, press the ON button to confirm the command. ("STEP 8" will display at the bottom of the screen. ) NOTE : Don't worry about the number of steps. Each macro button can store up to 190 steps, so you are not likely to run out of steps! STEP 12: Press the LIGHT button to end your macro. A new screen will appear: STEP 13: If you are satisfied with your macro, press the SAVE display button. The UNDO display button lets you erase the last step. The EXIT display button erases all the macro steps. STEP 14: Press the MAIN button twice to return to normal operation. STEP 8: Then, press the ON button to confirm the command. ("STEP 5" will display at the bottom of the screen. ) You can also program delays in between commands by pressing the (II) PAUSE button. Each press adds half a second to the delay. CUSTOMIZING STEP 9: Now, press the MAIN button to return to the Main Component listing. ("STEP 6" will display at the bottom of the screen. ) CUSTOMIZING SAVE BUTTON UNDO BUTTON EXIT BUTTON STEP 10: Press the third component display button that you want the Macro to turn on (in this example, CABLE) and "CABLE" will display at the top of the screen. ("STEP 7" will display at the bottom of the screen. ) 29 MacroPowerTM Setup 30 Advanced Macro Options: SETTING UP A POWER OFF MACRO: Simply follow the same steps as outlined above, except press the OFF button in place of the ON button. SETTING A COMPONENT BUTTON AS MACRO: If you wish to set one of the Component buttons as a macro, in STEP 3, press the Page Up button twice. [. . . ] Now you can close your entertainment center doors, hide your Components, and still control them with ease. One of the best things about this is -- nothing has to be done to the RF20 for this feature to work. Every time you press a button on the RF20, it sends both a standard IR (Infrared Command) AND an RF (Radio Frequency) signal. If you install the PowerBlasterTM kit, it will automatically receive RF20's radio signals and translate them into the infrared commands that control your Components. NOTE: The RF20's radio signals will not control Components directly. [. . . ]