User manual UNIVERSAL REMOTE CONTROL RF30 MASTERCONTROL

[. . . ] 1 The RF30 Remote Congratulations! Congratulations on purchasing Universal Remote Control's MASTERCONTROLTM RF30 Pre-programmed and Learning Remote Control!You now have the power to control your entire home entertainment system with one easy-to-use remote. The RF30 can be used with thousands of audio/video Components because of the extensive code library pre-programmed into the remote. And, the RF30's impressive lineup of special advanced features can automate and customize the operation of your system in many ways. [. . . ] The bottom of the screen displays "STEP0", indicating that you have not entered the channel number yet. STEP 6: Press each of the number buttons for the channel. Note: If a number is repeated when setting the channel (for example, channel "33" or "522'), it is usually best to set a half second delay in between the identical numbers by pressing the (II) PAUSE button. Each press of the PAUSE button increases the delay by a half second. CUSTOMIZING CUSTOMIZING FAV BUTTON PAUSE BUTTON DEVICE BUTTONS NOTE: Some brands of television require an ENT (Enter) command after the channel numbers. 25 Favorite Channel Setup 26 MacroPowerTM Setup MacroPowerTM is a unique feature that enables you to turn all of your Components ON or OFF, at the same time, simply with the press of one button. What would normally take multiple remotes and button pushes, the RF30 can accomplish with the press of one button. In addition to the Power ON or OFF buttons, any of the Display buttons (on any Component or Page) can be set to be Macro buttons as well. To setup a Power ON macro button that will turn ON several components at the same time (for example, TV, VCR and CABLE), follow these easy steps: STEP 7: Press the LIGHT button after you enter the channel number. A new screen appears displaying SAVE, UNDO or EXIT. MacroPower Setup STEP 8: To save the channel you entered, press the SAVE button. The UNDO button lets you erase the last entry. The EXIT button erases all entries for this button. STEP 1: Press and hold the MAIN and ENT (Enter) buttons at the same time for approximately 3 seconds, until the word "SETUP" is displayed at the top of the LCD touch screen. This signals that you are now in setup mode. IMPORTANT:You now have 30 seconds to perform the next step while you are in SETUP mode. If you don't press a button within 30 seconds, SETUP will disappear from the screen, signaling that you have exited setup mode and you will need to start over. STEP 4: Press the first component button you want the Macro to turn on (in this example, TV) and "TV" will display at the top of the screen and "STEP 1" at the bottom. STEP 9: When you are finished setting up Favorite Channel buttons, press the MAIN button twice to return to normal operation. STEP 5: Then, press the ON button to confirm the command and "STEP 2" will display at the bottom of the screen. (NOTE: Whenever a button is pressed, another Macro step is counted and displayed at the bottom of the screen. ) STEP 2: CUSTOMIZING SAVE BUTTON Press the MACRO button on the LCD screen. The top of the screen will display "MACRO". The bottom of the display will flash "SELECT". CUSTOMIZING STEP 6: Now, press the MAIN button to return to the Main Component listing. ("STEP 3" will display at the bottom of the screen. ) STEP 3: Press the ON button. "ON" will display at the top of the LCD screen. "STEP0" will display at the bottom of the screen indicating that no macro steps have been entered yet. 27 MacroPower Setup 28 MacroPower Setup STEP 7: Press the second component that you want the Macro to turn on (in this example, VCR) and "VCR" will display at the top of the screen. ("STEP 4" will display at the bottom of the screen. ) STEP 11: Then, press the ON button to confirm the command. ("STEP 8" will display at the bottom of the screen. ) NOTE: Don't worry about the number of steps. Each macro button can store up to 190 steps, so you are not likely to run out of steps! STEP 12: Press the LIGHT button to end your macro. A new screen will appear: STEP 14: Press the MAIN button twice to return to normal operation. STEP 13: If you are satisfied with your macro, press SAVE. The UNDO button lets you erase the last step. The EXIT button erases all the macro steps. STEP 8: Then, press the ON button to confirm the command. [. . . ] Now you can close your entertainment center doors, hide your Components, and still control them with ease. The RF30 sends radio signal to the PowerBlasterTM, which is a radio receiver. `Barroer -Free' RF control The PowerBlasterTM converts radio signals to standard infrared commands and sends them out via a built-in front blaster to Components in the same cabinet space. THE POWER BLASTER THE POWER BLASTER One of the best things about this is - nothing has to be done to the RF30 for this feature to work. Every time you press a button on the RF30, it sends both a standard IR (Infrared Command) AND an RF (Radio Frequency) signal. If you install the PowerBlasterTM kit, it will automatically receive RF30's radio signals and translate them into the infrared commands that control your Components. NOTE: The RF30's radio signals will not control Components directly. [. . . ]