User manual UNIVERSAL REMOTE CONTROL UR5U-8700 SPECS SHEET

[. . . ] The Component LED light will blink twice to confirm that the code was successfully stored. Now, program the rest of your Components by repeating STEPS 1-5. *Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the AutoSearch Method as explained in Section B. STEP4 Test functions. (Same as for 3-Digit Code Programming Method - Section A). [. . . ] If any of the functions do not work as they should, you need to find a new code. STEP5 Once you have found the correct 3digit code, save it by pressing the [AUX] button one more time. The Component LED light will blink twice to confirm the code was stored. Now when you press the AUX button, all the buttons will work with that 5th Component. G. Programming Volume Control channel you want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered. CBL-CABLE Converters Manufacturer/Brand SCIENTIFIC ATLANTA PIONEER PACE SAMSUNG MOTOROLA GENERAL INSTRUMENT HAMLIN HITACHI JERROLD MAGNAVOX MEMOREX MOXI PANASONIC PHILIPS PULSAR RCA REGAL REGENCY SKY SONY SPRUCER TOCOM TOSHIBA VIEWSTAR ZENITH Set-Up Code Number 001 003 041 042 045 046 001 103 034 051 063 076 105 001 005 002 001 030 002 111 148 005 103 104 049 050 055 103 055 005 004 103 005 003 008 009 010 069 010 012 052 111 252 044 047 006 012 013 020 085 052 047 049 050 057 230 108 047 039 040 056 052 012 015 052 060 093 100 E. Programming the System On/Off Button This allows you to program the System On/Off button so it can send up to five power On/Off commands with one button press. STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds. STEP3 Press the first [COMPONENT] button you want to store in the [SYSTEM ON/OFF] button and then the [POWER] button. Repeat this for other Components until you have stored all the desired power commands into the [SYSTEM ON/OFF] button. STEP4 Press the [CH ] button to save the power commands you stored. The [CBL] button will blink twice to confirm the commands have been saved. Volume and Mute control are factory- STEP4 Press the [CH ] button to store the channels that were selected. The [CBL] programmed to automatically transfer to the button will blink twice to confirm the respective Component mode you select, as storage of commands. follows: To access the programmed channels, press the [MACRO] button once. Press once again and it will However, you can program the volume controls bring up the second channel. Press again and (Volume Up, Volume Down and Mute) from one it will bring up the third channel. Component to operate in another Component. CBL : CBL DVD: TV T V : TV AUX: AUX VCR: TV If you wish to store the TV volume control in I. Low Battery Warning CBL mode, use the following steps. [. . . ] STEP1 Turn on the 5th Component you want to program (TV, VCR, DVD or Audio). STEP2 Press the [AUX] button and the [OK/SEL] button simultaneously for 3 seconds. The [AUX] Component LED will turn on for 30 seconds. STEP3 Press the [COMPONENT] button you want to setup. Point the remote control toward the Component and enter the 3digit code number assigned to your brand. Set-Up Code Number 112 143 025 036 072 251 333 247 388 002 103 116 146 248 404 405 473 475 323 387 391 017 028 043 073 052 043 054 056 080 112 116 363 112 058 006 573 574 477 076 454 388 052 441 039 The Component LED will blink twice to confirm the programming. F. [. . . ]