User manual UNIVERSAL REMOTE CONTROL WR7

[. . . ] WR7 1/13/08 12:18 PM Page 1 WR7 1/13/08 12:18 PM Page 2 Congratulations! Congratulations on purchasing Universal Remote Control's WR7 7-Component Pre--Programmed and Learning remote control. You now have the power to control your entire home entertainment system with one easy--to--use remote. The WR7 can be used with thousands of audio/video components because of the extensive library of codes that have already been programmed into the remote. get ready to sit back, relax, and simplify your home entertainment experience. [. . . ] Now test all the buttons to make sure they learned correctly. Repeat Steps 1-5 to program any other component modes. If the Learning Method does not work, here are a few suggestions: · If you have a Plasma TV, move to another room · Avoid programming under fluorescent light or direct sunlight · Put new batteries in the old remote · Gradually vary the distance between the two remote controls · Adjust the angles of the remotes (i. e. , keep the WR7 on a flat surface while holding the other remote in hand and angling it down toward the WR7) · Tap the button on your old remote instead of pressing and holding it during the learning process Page 17 WR7 1/13/08 12:18 PM Page 18 Here are some additional facts regarding the Learning process: · Learned functions override any existing pre-programmed functions on the remote control · Learned functions are automatically erased when a new function is learned on the same button · Learned functions are retained even after a different set-up code number is programmed into the remote control · To return to an original pre-programmed function, a learned function must be erased · Rapidly tapping the Volume Up button on the old remote will teach the WR7 to ramp the volume instead of raising it in increments of one Page 18 WR7 1/13/08 12:18 PM Page 19 AUX Function: Programming a 7th Component After you've finished programming the WR7 for six primary components and you did not use AUX, you can take advantage of the AUX function to program a 7th component, such as a second TV, DVD, or any other audio/video component that you may have in your system. Simply program the [AUX] button in the same manner as any other component using either the Quick Set-Up Method, the 3-Digit Code Entry Method, the Auto-Search Method or the Learning Method. Finding a Component's Set-up Code Number If you used the Auto--Search or Learning Methods to program a component, you may not know the code number you programmed. Here is a way for you to identify what that code number is, so you can make a note in the back of this Manual for future reference. STEP 1: Press the component button you would like to verify and the SELECT [SEL] button at the same time for two seconds until the selected component LED light turns on. IMPORTANT: You have 30 seconds to perform the next step while you are in programming mode. If you do not press a button within 30 seconds, the component LED light will turn off. The remote will exit the programming mode and you will have to start over. COMPONENT BUTTONS INFO SELECT Page 19 WR7 1/13/08 12:18 PM Page 20 STEP 2: Press the [INFO] button and count the number of times the Component LED light blinks. This number indicates the first digit of the code. Next it will pause for about one second and begin blinking again to indicate the number of the second digit. Then once again it will pause, then blink, to indicate the number of the third digit. Example: One blink, pause, eight blinks, pause, three blinks indicates code number 183. Note that ten (10) blinks represent the number 0. Page 20 WR7 1/13/08 12:18 PM Page 21 Programming Special Advanced Features Programming Multi-Commands to Macro Buttons The WR7 has 13 Macro buttons (ON, SYSTEM OFF, 7 Component buttons, and 4 `My Favorites' buttons) that are designed to store up to 20 commands in each button. Pressing any one of the Macro buttons will send out the series of commands that are stored in that particular button. MacroPowerTM Total System On/Off MacroPower makes several devices work together by pressing one button. Imagine the convenience of turning on your TV, your DVD player and your Surround Sound receiver by pressing a single button on your WR7. What could normally take three remotes and three button pushes, the WR7 can accomplish with the press of one button. Any of the Power On or the System Off buttons can be programmed for MacroPower control. To set it up, follow these easy steps: STEP 1: To program MacroPower commands for the POWER [ON] button, press the POWER [ON] button and the [MUTE] button at the same time for two seconds until one of the component button LED lights turns on. POWER MUTE Page 21 WR7 1/13/08 12:18 PM Page 22 IMPORTANT: You have 30 seconds to perform the next step while you are in programming mode. If you do not press a button within 30 seconds, the component LED light will turn off. The remote will exit the programming mode and you will have to start over. STEP 2: Press the component button you want to turn on and then the POWER [ON] button; repeat for all other components in the order you want them to turn on. The component LED lights will blink once each time you press the POWER [ON] button. POWER COMPONENT BUTTONS STEP 3: Once you've entered all the Power On commands, press the CHANNEL Up [CH ] button to save your MacroPower commands. [. . . ] IMPORTANT: If you don't proceed to the next step within 30 seconds, the LED will turn off and exit set-up mode and you will need to start over. STEP 2: Press the CHANNEL UP [CH ] button to erase and exit Erase mode. The component LED light will blink three times to confirm the erasure. POWER ON SYSTEM OFF CHANNEL UP MUTE NOTE: To erase other Macros, simply press the appropriate button in Step 1 in combination with the [MUTE] button. Page 32 WR7 1/13/08 12:18 PM Page 33 Erasing SimpleSound & Other `Punch Through' Commands STEP 1: Press and hold the Component button you want to erase volume control from, such as DVD or VCR and the SELECT [SEL] button at the same time for two seconds until the Component LED light turns on. STEP 2: Press the VOLUME UP [VOL ] button and the same component button from Step 1. [. . . ]