User manual UPM WS2635

[. . . ] (-20 to +50ºC) Local Humidity Display (WS2635H only) Receive and display up to 4 remote temperature zones with maximum and minimum temperature memory from the Remote Transmitters (-30 to +70ºC) Receive and display up to 4 remote humidity levels from the Remote Transmitters (when using WT260H transmitter only) Clock function has selectable 12 / 24 hour format. Alarm Clock with Snooze function Kitchen Countdown Timer with reminder function Distinctive sound patterns for different alarm functions User-selectable Temperature Display Combinations Low-Battery Indication Battery installation of Remote Transmitter Unscrew the battery cover from the back of the Remote Transmitter. Insert two 1. 5V AAA batteries (included) into the battery compartment. Make sure the battery is inserted in the correct polarities as marked. [. . . ] House code will be flashing '01'. Wait for 12 seconds to accept this value. Device code will be flashing '1'. If you have only one transmitter, just wait for 12 seconds to accept this value. If you want the display in °F , press SET button at the back ONCE. If you have more than 1 transmitter, repeat the above for the other transmitter while selecting different Device code. Features of Remote Transmitter WT260 / WT260H Temperature Display in ºC or ºF Humidity Display (WT260H only) Compact size with Wall-mount holder Drip-proof design Transmit temperature and humidity (WT260H only) data by RF Technology to the Weather Station 5 Press MODE or /CHANNEL to increase or decrease its value. To confirm the entry and move to the next item, press SET. Repeat above steps until all data has been set. For the setting of Second, it can be set to "00" of the present minute by pressing CHANNEL or "00" of the next minute by pressing MODE . To change between 12 and 24 hour display, press ST/SP while setting clock. Press SET while Second is flashing to end the clock setting. Kitchen Countdown Timer To set the Countdown Timer press SET in Countdown Timer , mode. The House Code will be confirmed if no key is pressed for 12 seconds. Channel Number will start to flash with "1" as in Figure 8. Setting the Weather Station as Receiver The Weather Station needs to execute the Learn function to identify the transmitters present and their transmission sequence. To start the Learn function, press and hold SNOOZE for 3 seconds. "RF THERMO" symbol will flash and a beep sound will indicate that the Learn function has been activated. The Weather Station will search for signals from Transmitter(s) nearby and use the first House Code received as its own House Code. Whenever a valid data is received, a beep will sound and the temperature and channel number will be displayed on the Right Display Box of the Weather Station as in Figure 10. Local Temperature / Humidity Display Initially, the local temperature of Weather Station will be displayed on the Display Box at the bottom left. To change from °C to °F display or vice versa, press the ST/SP key while the clock is displayed. Press SNOOZE to scroll through the displays of Current Temperature, Maximum T emperature (Figure 5) and Minimum Temperature recorded (Figure 6). To scroll through the displays of Current T emperature, Maximum Temperature and Minimum T emperature from the Transmitter, press the SNOOZE key. If the remote temperature display starts to flash, it indicates that the signal is temporary lost. This may be due to interference from nearby electrical appliances or environment. You can wait for a while to see if the flashing will stop because most interference is temporary. Sometimes the signal received is too weak and you can try to move the Weather Station and/or Transmitter to a different location to have better reception of the signals. [. . . ] Left box - Press and hold CHANNEL for 3 seconds to scroll through the following display modes: Local CH. 1 CH. 2 CH. 3 CH. 4 Local In the Auto Display Mode, all 4 Channel Numbers under the Right box will be displayed. In this mode, the display will scroll through data from all the valid channels, each of which will be shown for 20 seconds. FIGURE 13 In each case, batteries should be replaced. After installation of new batteries, the set up procedure will need to be performed again. Technical Specification Weather Station WS2635 2 x 1. 5V AA size batteries (or equivalent) From 1 Sec. (Resolution: 1 Second) Detectable Temperature Range: From - 20ºC to +50ºC (Resolution: 1ºC [Below - 10ºC]; 0. 1ºC[Above - 10ºC]) Range of Countdown Display: Battery Type: Wall-Mounting for Remote Transmitters C C With the wall-mount holder, the Transmitters can be attached onto the wall easily by following the procedures below: FIGURE 12 1 RF THERMO 2 C C C C C C FIGURE 5 LOCAL MAXRF THERMO 1 LOCAL MIN RF THERMO 1 FIGURE 6 FIGURE 7 FIGURE 8 LOCAL RF THERMO To clear the records of Maximum and Minimum T emperature, press and hold ST/SP for 3 seconds while clock is displayed. [. . . ]