User manual UPM WT260H

[. . . ] I -. of II: 1 1. 3 Setting , -. -~:'. '. ~, ~-. 1I-mn llLlLlon ~ off. will appear. Check Remote Temperature & Humidity A $ Press CHN key to display readings of temperature the Channel and humidity and toggle and humidity the among Calendar 1, 2 and 3 displays. data will alternate. Temperature Alarm 1and Alarm 2 Setting Scroll using Press Press Press to ALARM 1 mode (ALARM 2 mode). [. . . ] 'Channel' symbol will flash and unit will beep as each remote transmitter is detected. Temperature & humidity readings of remote transmitter displays on the receiver. 4 * Use a different house code if your weather station receivesSignalsfrom other transmittersof neighboring sources. * If House code and Channel code are not selected (steps 3 & 5 are skipped), House code 01 and Channel code 1 will be default. 3 WEATHER DISPLAY temperature & humidily trend The trend indicator shows the trend of temperature and humidity determined by the particular transmitter in the past half-hour interval, o TEMPERATURE ALARM 8Sc o You can set the temperature alarm for the local main unit and for one outdoor channel separately. roll to Temperature Alarm mode using MODE. =~'ll. /lE , / ~ '-. I Arro~r~~:cator __ ~:i~7~=j-~~stea;-- j-" Falli: alarm weather report symbols The receiver is able to monitor and display the weather collected data from Channel 1. status based on Freeze 1_~ I I J s_u~ny Cloudy Raining Snowing Warning e ~;;~~:~~:~::'";;;~~;;:~;~":~; o 1~":Dj - Down arrow: Lower temperature limit - No arrow: Temperature alarm disabled J . ~i\l;. ". ""/"'~. ~-':'~"'O" ~c, ' . ~ Press + or - key to set the temperature limit value Weather Indicator D r , · . ', «: . ' j About Freeze Warning * Snow symbol will flash to warn of 'freezing'. * Activated when Channel 1's temperature is between -1 . 9 C and -12. 9 C. * Snow will appear solid if and when Channel 1's temperature falls below -1. 9 C. Note. : * Initially, the weather will be cloudy. * Remote transmitter Channel 1 will be used for weather indication. * If Channel 1 is empty, then weather will always be cloudy. * If Channel 1 has no humidity data, weather indication will always be cloudy, but freeze warning and snow indication will be available. To set the temperature alarm for an outdoor channel, press ---MODE until the outdoor temperature flashes. Then use the CHN key to select the desired remote channel (1, 2 or 3). Repeat steps 3 and 4. When Temperature Alarm Sounds It is to alert that the actual temperature exceeds the preset temperature limit. Press any key to stop the temperature alarm: or If no key is pressed, the temperature alarm will automatically stop itself after one minute. Once triggered, the temperature alarm comes on as a distinctive sound, different to that of ALARM 1 and ALARM 2. Also, tile 'siren' symbol will flash. 8 9 CLOCK SETTING Clock 1 Setting: ['"/2D826=, "oc"i Clock 1 Setting ~~--~ Press and hold MODE for 3 seconds to enter the clock setting (the CLOCK 1 symbol appears and the time will flash). Press HOUR to set the hour and MIN to set the minute. [. . . ] and is subjected to the following two conditions: SPECIFICATIONS Weather Station Receiver WS290C - Battery Type: 2 X 1. 5V AA batteries - Operation Temp: -5 C to +50 C - Temp. Range: -20 C to +55 C - Measurement Accuracy: Max. +/- 1 C within measuring range of 0 to 40 C - Resolution: 0. 1 C Weather Station Transmitter WT260H - Battery Type: 2 X 1. 5V AAA batteries - Operation Temp. : -20 C to +60 C - Temp. [. . . ]