User manual US ELECTRONICS NOVARI SA

[. . . ] When the DVD key is selected, the up and down keys perform skip forward and backward functions. GUIDE displays the program guide SELECT FAV EXIT EXIT exits out of on-screen menus LAST recalls the last channel that was viewed VOL CH LAST SELECT chooses the highlighted item in the menu FAV steps through favorite channels A MUTE CH changes the channel up and down C B VOL turns the volume up and down 1 4 2 5 8 0 3 6 9 # FF NUMBER KEYS allow direct access to specific channels and menu options 7 PPV MUTE turns volume on/off The Scientific-Atlanta® Explorer set-top box has an on-screen program guide that can be sorted several different ways: A browse by title, channel, or theme B browse by date C browse by current time Consult your set-top box manual for more information on the on-screen guide When operating Tivo, A and C perform the skip forward and back functions. # functions as an ENTER key on devices that require ENTER to be Pressed after inputting a channel with the number keys. REW PLAY ! © 2003 US Electronics, LLC. All rights reserved Part Number USE18220 , version 2. 0 01282003 IMPORTANT NOTE Weak batteries may disrupt normal operation of the remote. We recommend that you use only new Alkaline AA batteries. VCR KEYS perform standard VCR functions when the VCR or TV keys are selected, and DVD functions when the DVD key is selected. [. . . ] If the device key does not flash three times before turning off, the code is invalid for this device type. Repeat the procedure with another device code. 8 SmartScanTM If none of the codes listed for your device works, the SmartScanTM procedure will allow you to cycle through all the available codes in the remote until you find the right one. 3 Point the remote at the device and press POWER. If the device turns on or off, you have finished programming. If you have tried all the codes listed for the manufacturer and the device does not respond, refer to the CodeScanTM section later in this manual. 1 2 Manually turn on power to the device for which you want to program the remote (TV, VCR, DVD, AUDIO). Press and hold the appropriate device key for approximately three seconds until the five device keys flash twice. The selected device key will continue to flash. The device key will stop flashing and remain on. Approximately once every second, the remote sends the power-off command using a different device code. When the device turns off, that means that the remote has reached a code that can control the device. Immediately release the UP ARROW key when the device turns off. If you accidentally press the UP ARROW key after the device has turned off, press the DOWN ARROW key to return to the previous device code. The Up Arrow Key 4 Write the codes below 025 Set-top Box code ___ ___ ___ VCR code ___ ___ ___ 3 TV code ___ ___ ___ Audio code ___ ___ ___ DVD Code ___ ___ ___ 5 PROGRAMMING VOLUME CONTROL By default, the TV, CBL, or AUD keys will send their own volume and mute signals to their device. If you would like to set up the Novari so that volume is always controlled by a particular device (set-top box, TV, or audio amplifier), follow these steps: 4 1 2 Press and hold the CBL key for approximately three seconds until the five device keys flash twice. Press VOLUME UP then VOLUME DOWN then the Device Key (TV, CBL, or AUD) of the device that you want to control volume and mute functions. After you release the Device Key, the CBL key will blink three times to confirm the procedure. Test whether other functions operate using the remote control. If a primary function does not work, continue to press the UP ARROW key to find another code that turns off the device. When you are satisfied that all primary functions are working, press SELECT to lock in the code. 9 RECALLING A DEVICE CODE NOTE: volume will always be controlled by your audio device when the remote control is in AUD mode -- regardless of how you set up volume control in this section. Perform the following steps to read the code currently set for a device. This is useful for retrieving a device code that was set using the CodeScanTM procedure. 6 MASTER POWER CONTROL 1 2 Press and hold a device key until the five device keys flash twice. The selected device key will continue to flash. The device key flashes each of the three digits in the code. For example, three flashes represent the number 3, and a rapid flicker represents 0, so a code of 103 will be shown as: FLASH <pause> FLICKER <pause> FLASH FLASH FLASH Count and record the sequence of flashes to determine the three-digit code. You can program your Novari to turn on and off all of your remote-controlled devices (TV, CABLE, VCR, DVD, AUDIO) when you press POWER. All devices must be in direct line of sight to ensure proper operation. Perform the following steps to enable or disable power control for each device: 1 2 3 Make sure all devices to be controlled are turned on. [. . . ] Consult related owners manuals for specific installation and operation instructions for each device. Problem The channel keys only operate my set-top box. Solution Make sure that Channel Lock isn't engaged. Follow the steps in section 7 to disengage Channel Lock. [. . . ]