User manual US ROBOTICS USR9002 INSTALLATION GUIDE

[. . . ] ADSL USB/Ethernet Modem Quick Installation Guide for Windows 95B (OSR2), 98, NT 4. 0, 2000, Me, XP (or later), Linux, and Macintosh Operating Systems * English Model 9002 Part Number R24. 0265. 00 * USB is not supported in Windows 95 and NT 4. 0 0 Table of Contents Installation Overview & System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 What You Need Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Computer Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Should You Connect via Ethernet or USB?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Windows Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Step 1. [. . . ] (For Windows Users Only) Run a test using the U. S. Robotics SureConnect ADSL Utility to identify any possible problems. For more information about how to run a test, refer to the "U. S. Robotics SureConnect ADSL Utility" section of this Quick Installation Guide. The graphic below shows the U. S. Robotics SureConnect ADSL USB/Ethernet Modem connected to an ISP. The ADIModem interface is loaded (local IP 192. 168. 60. 30), and the ppp0 interface is up and running with an IP address (80. 11. 157. 151) and a gateway (80. 11. 157. 1). Modem Status To view various statistics about the modem and the connection, run the following script: USR_USB/ADI_PPPOE/. /showstat The statistical information will be available through ADIModem in /proc directory. This feature is available as soon as you plug the USB cable in. Status LEDs The U. S. Robotics SureConnect ADSL USB/Ethernet Modem has four LEDs on the front of the modem. The first from the left is the "PWR" LED, the second is the data transfer "ENET" LED, the third is the "USB, " and the last is the "ADSL" LED. The operational status of the modem is indicated by the LED conditions listed below. 26 27 26 27 · PWR Power is being received from the power supply in the wall jack. A physical connection between the modem and the comOn Green puter, through the Ethernet cable, has been established and detected. A physical connection between the modem and the comOff puter, through the Ethernet cable, has not been established. A physical connection between the modem and the comOn Green puter, through the USB cable, has been established and detected. A physical connection between the modem and the comOff puter, through the USB cable, has not been established. On Green A DSL link has been established. Flashing Green A DSL link is being negotiated. On Green · ENET · Confirm that you are using the power adapter that came with the U. S. Robotics ADSL USB/Ethernet Modem and that it is securely plugged into a wall outlet and the modem. If you are connecting via Ethernet, confirm the network interface card (NIC) did acquire an IP address. Restart the computer and then run the test again. If the Modem test still fails, contact your ISP to verify the operational status of the modem. USB ADSL Troubleshooting Tips Windows Only None of the LEDs are illuminated when the ADSL modem is powered on. Check the connection of the power adapter to the modem and to the wall outlet. Confirm that you are using the power adapter that was included with your U. S. [. . . ] Return the product to: In the United States: USR-Walnut 528 Spanish Lane Walnut, CA 91789 In Canada: U. S. Robotics Unit - 100 13751 Mayfield Place Richmond, B. C. Canada V6V 2G9 38 39 38 39 WARRANTIES EXCLUSIVE: IF A U. S. ROBOTICS PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY FOR BREACH OF THAT WARRANTY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT U. S. [. . . ]