User manual VARIZOOM FLOWCAM GT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual VARIZOOM FLOWCAM GT. We hope that this VARIZOOM FLOWCAM GT user guide will be useful to you.

Lastmanuals help download the user guide VARIZOOM FLOWCAM GT.


Mode d'emploi VARIZOOM FLOWCAM GT
Download
Manual abstract: user guide VARIZOOM FLOWCAM GT

Detailed instructions for use are in the User's Guide.

[. . . ] To achieve optimal results, you should adjust the vest so that it fits snugly. Adjust the vertical fit by adjusting the straps, pulling the chrome release pin and sliding the chest plate up or down until you find the right position. Adjust the tightness of the vest around your waist/hips using the Velcro strap, drawing it around evenly on both sides of the lower vest pad. Adjust the tightness around your torso by positioning the Velcro straps across the back of the vest and securing the buckles to the chest plate. [. . . ] Operator skill is critical, and it takes many hours of practice to master this device, but the reward for all the practice will be substantial. Here are a few simple quick-start guidelines: -Hold the system by the gimbal handle to control the orientation and elevation of the sled. -With the other hand, lightly grasp the center post of the sled just below the gimbal, holding it close to the gimbal for optimal control. -Delicately grasp the center post with your fingertips, like a flute ­ do not grab it like a handlebar. -Practice good posture and hold the sled close to your body. -Fine-tuning of the balance adjustments may be necessary a few times during operation. -The way you walk will affect the quality of stabilization, so you will need to develop a lightfooted rhythmic pattern. -Practice for at least 20 hours before attempting to acquire usable footage. The DVD contains detailed, clear instructions and tips on operation, and if you have any general questions, visit the website ­ www. varizoom. com. If you've watched the video and practiced and still have technical questions, call 310545-0466. Page 3 The Sled The Sled is the subsystem that holds the camera, viewing monitor, and battery. The Sled mounts to the arm, and in tandem they create a stabilizing effect. The Sled can be adjusted at various points to change its weight distribution, which in turn enables you to accommodate cameras of different sizes, shapes and weights. The basic principles of sled adjustment are that you want the section of the sled below the pivot point to be effectively heavier (slightly) than the upper section, and you want the camera's mass to be centered on the rotating axis. The Sled consists of three main sections: The Stage enables you to adjust the horizontal balance of the system and also houses the video and power connectors. The Post and Gimbal provide smooth pan and tilt action, a mounting socket for the spring arm, and a grip handle. This section also features one of several vertical balance adjustment points. The Lower Sled holds the LCD monitor and the battery power source. This section provides a few vertical and horizontal balance adjustment points. Page 6 If your fully loaded camera weighs less than 6 pounds, you will have to remove the non-adjustable spring. If it weighs more than 11 pounds, you will have to replace the nonadjustable spring with a heavier one. A1 ­ Start by opening the arm (see below) Once you've removed the two screws, you will be able to swing the top half of the arm out and have access to the inside of the arm. Page 7 Remove two hex screws, one from each side at the top of the arm, as pictured (5/64" key, not included) Next, remove ONLY the spring attached to the stationary bar ­ NEVER remove the spring on the adjuster assembly. Remove the spring from the stationary bar by grabbing it along its length and pulling it up and over the bar. Fold the arm back together and replace the screws. = adjuster spring + light spring on stationary bar 11-16 lbs. [. . . ] Now you can proceed with the horizontal balancing, which is accomplished by adjusting the longitudinal and lateral positions of the camera. First you will have to loosen the dovetail lock. If the sled tilts forward or backward, you can adjust the position of the dovetail using the knob at the front of the stage. If the sled tilts to one side, you can adjust the Page 5 stage laterally by using the second knob. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE VARIZOOM FLOWCAM GT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual VARIZOOM FLOWCAM GT will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag