User manual VDO CYCLECOMPUTING HC12.6

[. . . ] CYCLECOMPUTING INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D´INSTALLATION ET D´UTILISATION MANUALE D´INSTALLAZIONE E FUNZIONAMENTO INSTALACION Y OPERACIÓN MANUAL HANDLEIDING HC12. 6 P1 screw P2 P3 1-5 mm P4 LOCK UNLOCK P5 OPEN CLOSE P6 P7 IMPORTANT Rubber washer CLOSE OPEN P8 Press AC-Button to Begin or install battery (P6) automatic ······· Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select P9 1x WS in mm / inch P10 ETRTO 47-305 47-406 34-540 47-507 23-571 40-559 44-559 47-559 50-559 54-559 57-559 37-590 20-571 16x1, 75 20x1, 75 24x1 3/8 24x1, 75 26x1 26x1, 5 26x1, 6 26x1, 75 26x1, 9 26x2, 00 26x2, 125 26x1 3/8 26x3/4 WS in mm KMH 1272 1590 1948 1907 1973 2026 2051 2070 2089 2114 2133 2105 1954 WS in inch MPH 50, 1 62, 6 76, 7 75, 1 77, 7 79, 8 80, 7 81, 5 82, 2 83, 2 84, 0 82, 9 76, 9 ETRTO 32-630 40-622 47-622 40-635 37-622 18-622 20-622 23-622 25-622 28-622 32-622 37-622 40-622 27x1 1/4 28x1, 5 28x1, 75 28x1 1/2 28x1 3/8 700x18C 700x20C 700x23C 700x25C 700x28C 700x32C 700x37C 700x40C WS in mm KMH 2199 2224 2268 2265 2205 2102 2114 2133 2146 2149 2174 2205 2224 WS in inch MPH 86, 6 87, 6 89, 3 89, 2 86, 8 82, 8 83, 2 84, 0 84, 5 84, 6 85, 6 86, 8 87, 6 P11 SET Metric System SET WS 1 Start at TRIP DIST Press MODE 1 for 3 sec. Press MODE 2 to select between KMH and MPH Press MODE 1 to set WS1 ············ Press MODE 2 to increase · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·· · · · · · SET WS 2 ····· ····· Press MODE 1 to switch and MODE 2 to increase continue for all4 digits Press MODE 1 3 sec. to end Press MODE 1 to switch Press MODE 2 to increase Press MODE 1 to set WS2 Press MODE 1 3 sec. to end without setting WS2 P12 Press MODE 1 3sec. to start Press MODE 2 to switch between 24h or 12h Press MODE 1 to set the hours MODE 2 to increase the hours Press MODE 1 3 sec. to end Press MODE 2 to increase the minutes Press MODE 1 to set the minutes P13 P14 Set Press MODE 1 3sec. to start Press MODE 2 to increase Press MODE 1 to switch Press MODE1 3 sec. [. . . ] These instructions can be precisely followed by using the NAVIGATOR. Once you have arrived at the first intersection after the first mile, you reset the NAVIGATOR to zero and and follow the next leg for half of a mile. At the second intersection you reset to zero again and follow the next instruction of your road book. The NAVIGATOR can be preset and proceed from this individual value. For example, you are unable to start your tour at the point 0 km/m, but at 5. 3 km. This value can be preset / entered into the NAVIGATOR. The NAVIGATOR will then count on from 5. 3 km. Also after a mistake in following the road book, you can reset/reenter the correct value. 4. 4. 1 Presetting the NAVIGATOR Step 1: MODE 2 calls NAVIGATOR into display Step 2: Press MODE 1 for 3 sec. The lower part of the display alternetely shows "ENTER NAVIGATOR" and "000. 00" with the last digit "0" flashing. Step 3: By pressing MODE 2 you increase the flashing number, by pressing MODE 1 you jump to the next number 000. 00, etc. Step 4: Once the NAVIGATOR is preset, exit setup mode by pressing MODE 1 for 3 sec. The display shows NAVIGATOR and the preset value. Your VDO HC 12. 6 will be counting on from this preset value. P13 4. 4. 2 Resetting the NAVIGATOR to zero Step 1: MODE 2 calls NAVIGATOR into display Step 2: Press MODE 2 for 5 sec. , the value indicated is being reset to zero. Your VDO HC 12. 6 will be counting on from zero. Warning: Before resetting to zero, make sure the information NAVIGATOR is called in. If NAVIGATOR is not in the display, you are accidentally re-setting other information to zero. P14 10 4. 5 Presetting the odometer After a battery change, you can re-enter previous odometer values (for both bikes) into your VDO HC 12. 6. Step 1: With MODE 2 call "ODO1 METER" or "ODO2 METER" into display, depending which one of these values you want to re-enter. The lower part of the display alternately shows "ENTER ODO1 METER" or "ENTER ODO2 METER" plus the respective value with the last number flashing. Step 3: With MODE 2 you increase the number, with MODE 1 you jump to the next number etc. Step 4: Once you have entered your values for ODOMETER 1 and ODOMETER 2, you exit set-up mode by pressing MODE 1 for 3 sec. [. . . ] "FREEZ" indicates that status. TIME IN indicates the time your pulse / heart rate is within the preset upper and lower limit window, i. e. 1:14:40 h:mm:ss This window is your desired target range zone in which you should be most of the time to achieve optimum results. Same here, "FREEZ" indicates the STOPWATCH has been put to a manual halt and time zone registering is interrupted. [. . . ]