User manual VDO CYCLECOMPUTING MC1.0

[. . . ] CYCLECOMPUTING INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D´INSTALLATION ET D´UTILISATION MANUALE D´INSTALLAZIONE E FUNZIONAMENTO INSTALACION Y OPERACIÓN MANUAL HANDLEIDING MC1. 0 P1 screw P1 P2 P4 LOCK UNLOCK 2. UNLOCK P5 P6 P7 Press AC-Button to Begin or install battery (P6) automatic ······· Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select P8 1x WS in mm / inch P9 ETRTO 47-305 47-406 34-540 47-507 23-571 40-559 44-559 47-559 50-559 54-559 57-559 37-590 20-571 16x1, 75 20x1, 75 24x1 3/8 24x1, 75 26x1 26x1, 5 26x1, 6 26x1, 75 26x1, 9 26x2, 00 26x2, 125 26x1 3/8 26x3/4 WS in mm KMH 1272 1590 1948 1907 1973 2026 2051 2070 2089 2114 2133 2105 1954 WS in inch MPH 50, 1 62, 6 76, 7 75, 1 77, 7 79, 8 80, 7 81, 5 82, 2 83, 2 84, 0 82, 9 76, 9 ETRTO 32-630 40-622 47-622 40-635 37-622 18-622 20-622 23-622 25-622 28-622 32-622 37-622 40-622 27x1 1/4 28x1, 5 28x1, 75 28x1 1/2 28x1 3/8 700x18C 700x20C 700x23C 700x25C 700x28C 700x32C 700x37C 700x40C WS in mm KMH 2199 2224 2268 2265 2205 2102 2114 2133 2146 2149 2174 2205 2224 WS in inch MPH 86, 6 87, 6 89, 3 89, 2 86, 8 82, 8 83, 2 84, 0 84, 5 84, 6 85, 6 86, 8 87, 6 P10 SET Metric System SET WS 1 Start at TRIP DIST Press MODE 1 for 3 sec. Press MODE 2 to select between KMH and MPH Press MODE 1 to set WS1 ················ Press MODE 2 to increase · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·· · · · · · SET WS 2 Press MODE 1 to switch and MODE 2 to increase continue for all 4 digits ····· Press MODE 1 3 sec. to end Press MODE 1 to switch Press MODE 2 to increase ····· Press MODE 1 to set WS2 Press MODE 1 3 sec. to end without setting WS2 P11 SET Clock Press MODE 1 3sec. to start Press MODE 2 to switch between 24h or 12h Press MODE 1 to set the hours MODE 2 to increase the hours Press MODE 1 3 sec. to end Press MODE 2 to increase the minutes Press MODE 1 to set the minutes P12 P13 Set Navigator Press MODE 1 3sec. to start Press MODE 2 to increase Press MODE 1 to switch Press MODE1 3 sec. [. . . ] Step 5: With MODE 1 you start the minute setup. The minute display will be flashing and can be changed with MODE 2. Step 6: Once hours and minutes are correctly entered, you exit CLK set-up mode by pressing MODE 1 for 3 sec. P11 MC 1. 0 GB 11 2. 7 The NAVIGATOR GB MC 1. 0 The NAVIGATOR is a second, individual trip distance counter that can be: · manually reset to zero · preset to a certain value, the trip distance is then counted from this value. The NAVIGATOR is very helpful following road book instructions or tour suggestions of bike magazines. For example, your road book tour wants you "to go straight for a mile and then make a right turn, then go on for half a mile and make a sharp left turn". These instructions can be precisely followed by using the NAVIGATOR. Once you have arrived at the first intersection after the first mile, you reset the NAVIGATOR to zero and and follow the next leg for half of a mile. At the second intersection you reset to zero again and follow the next instruction of your road book. The NAVIGATOR can be preset and proceed from this individual value. For example, you are unable to start your tour at the point 0 km/m, but at 5. 3 km. This value can be preset / entered into the NAVIGATOR. The NAVIGATOR will then count on from 5. 3 km. Should you have made a wrong turn, return to that spot and enter your leg distance anew, continue to follow your roadbook instructions 2. 7. 1 Presetting the NAVIGATOR Step 1: MODE 2 calls NAVIGATOR into display Step 2: Press MODE 1 for 3 sec. The lower part of the display alternetely shows "ENTER NAVIGATOR" and "000. 00" with the last digit "0" flashing. Step 3: By pressing MODE 2 you increase the flashing number, by pressing MODE 1 you jump to the next number 000. 00, etc. Step 4: Once the NAVIGATOR is preset, exit setup mode by pressing MODE 1 for 3 sec. The display shows NAVIGATOR and the preset value. Your VDO MC 1. 0 will be counting on from this preset value. 12 2. 7. 2 Resetting the NAVIGATOR to zero Step 1: Step 2: MODE 2 calls NAVIGATOR into display Press MODE 2 for 3 sec. , the value indicated is being reset to zero. Your VDO MC 1. 0 will be counting on from zero. MC 1. 0 GB Warning: Before resetting to zero, make sure the information NAVIGATOR is called in. If NAVIGATOR is not in the display, you are accidentally re-setting other information to zero. 2. 8 Presetting (programming) the odometer After a battery change, you can re-enter previous odometer values (for both bikes) into your VDO MC 1. 0. [. . . ] Depending on the home altitude entered the actual altitude may read out differently. Re-calibrating the altimeter to absorb changes in barometric pressure Changes in barometric pressure make your VDO MC 1. 0 change the readout of the current / actual altitude. This new readout may differ from the value you have determined for your home altitude (= same location but changed barometric pressure). So before you go out for a ride, readjust the actual displayed altitude to your home altitude. [. . . ]