User manual VDO DAYTON CHD 1002 S

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual VDO DAYTON CHD 1002 S. We hope that this VDO DAYTON CHD 1002 S user guide will be useful to you.

Lastmanuals help download the user guide VDO DAYTON CHD 1002 S.


Mode d'emploi VDO DAYTON CHD 1002 S
Download
Manual abstract: user guide VDO DAYTON CHD 1002 S

Detailed instructions for use are in the User's Guide.

[. . . ] They should not exceed +70°C or ­20°C when operating the CD changer. · To avoid too high temperature, never install the changer on top of the dashboard or on the rear parcel shelf. - If the temperature is too high, a built-in protection mechanism prevents the CD changer from operating until the temperature reaches a safe level. During this time a warning message is displayed by the car radio. 2 INSTALLATION PREPARATION FIXING MATERIAL SUPPLIED Fig. [. . . ] After setting the position of the shock absorbers, glue the supplied stickers G over the holes of the setting mechanisms (CHD 1002S only). 4 MOUNTING GB A 1 Caution: Take care not to drill into the fuel tank, the exhaust pipe system, the catalytic converter or the cables laying behind or below any drilled holes! · To prevent dust and dirt entering the unit, glue the supplied stickers F over all unused mounting holes of the CD changer (see Figs. 10 and 18). MOUNTING IN THE LUGGAGE BOOT Fix brackets A (L) and (R) to the lower sides of the CD changer using the hexagonal bolts C (Figs. Fix the base-plates with the long hexagonal bolts to the brackets using the hexagonal nuts D (Fig. If present, lift the carpet covering the floor of the luggage boot. First glue the supplied double-sided self-adhesive tape to the base plates. Then carefully position the CD changer and apply pressure to glue it into place (Fig. The base plates must be glued to a clean, flat surface. 2 3 4 If there is no flat surface in the luggage boot, a wooden mounting board (approx. 10 mm thick) under the carpet should be used instead of the base plates. (Fix the wooden mounting board to the car using three screws). In that case fix the brackets to the board (laying under the carpet) using screws. 1 Remove the hexagonal nuts D. 15). 2 3 4 Lay the carpet over the base-plates (or the wooden mounting board) and cut four small crosses in the carpet. Check that the three transport screws have been removed from the underside of the CD changer!Mount the CD changer using the hexagonal nuts D (Fig. 17). MOUNTING IN SUSPENDED POSITION The CD changer can also be mounted on the underside of a flat surface, e. g. 1 Fix brackets A (L) and (R) to the upper sides of the CD changer using the hexagonal bolts C (Fig. 2 Place the CD changer in the mounting position (Fig. 19). 3 4 Mark positions for four mounting holes (with a felt-tip pen). Drill holes of 3. 6 mm diameter in the marked positions. 5 6 Check that the three transport screws have been removed from the underside of the CD changer!Hold the CD changer in place and attach it with the tapping screws E. 5 MOUNTING CONNECTING THE CABLES (Fig. 20) Only use the cables supplied to connect the CD changer to the car radio!1 Ensure that the negative car battery terminal is disconnected. 2 3 4 Connect the car radio as described in the car radio's mounting instructions. Connect the blue plug C3 of the extension cable to the rear of the car radio (socket C3') (fig. [. . . ] Insert disc without scratches or which is not warped. If sound from second disc is acceptable, first disc is defective. Remove screws (x3) on bottom of unit and then use. Adjust setting mechanisms in proper direction (refer to "Installation" in Operating Instructions). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE VDO DAYTON CHD 1002 S

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual VDO DAYTON CHD 1002 S will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag