User manual VELODYNE FSR-12 REV D

[. . . ] Packing this unit in any other carton may result in severe damage when shipping. Record the serial number in the space provided on page 13 for future reference. Product Features · A single driver consisting of either: - 10" (8. 2" piston diameter) subwoofer with 2. 0" high-temp voice coil and 40 ounce motor structure or, - 12" (9. 7" piston diameter) subwoofer with 2. 0" high-temp voice coil and 40 ounce motor structure · Adjustable (50 to 200 Hz) low-pass crossover with a 12 dB/octave slope · Line-level (RCA) inputs · Speaker-level inputs and outputs with spring loaded terminals · Signal sensing auto turn on/off · Variable volume control · Selectable phase control (0° or 180°) · Green power on/ Red power standby mode indicator LED Prepare for Installation Your new Velodyne subwoofer provides for a number of installation options. Read all the installation information below in order to determine which installation option is best for your system. Remember to perform all installation procedures with system power turned off to prevent possible damage. . www. velodyne. com VRP User's Manual 1 Placement True subwoofers operate at extremely low frequencies that are primarily omni-directional. [. . . ] Depending on the size and type of furnishings in the room, perfect placement may not be possible. Finding the best location for your environment will likely require some experimentation. We suggest you experiment with the location during setup to find what sounds best to you when seated in your typical listening position. I n s ta l l a t i o n Inputs Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when connecting your subwoofer to a pre-amp, signal processor (such as LFE out), linelevel crossover, or receiver with pre-amp level outputs. When using the line level jacks, some receivers may not provide enough signal to have the unit's auto-on feature operate properly. Additionally, this lack of signal may also cause the subwoofer to produce less output than it is capable of. . www. velodyne. com VRP User's Manual 2 To alleviate this condition, we recommend the following steps: 1) If using line level jacks, BOTH THE LEFT AND RIGHT INPUT SHOULD ALWAYS BE USED ­ never use just the left or just the right input. If the subwoofer's input comes from the LFE channel of your receiver, use the included "Y" splitter to divide the single input into two inputs for the Left and Right subwoofer inputs. If using line level connections from a preamp or signal processor, use both Left and Right inputs from your preprocessor or preamp and connect them to the Left and Right inputs on your subwoofer. If using a receiver with LFE out, be sure the LFE channel is sending adequate signal to the subwoofer. We recommend setting the subwoofer's level to the 9 o'clock position (the 1/4 volume setting) and then adjust the LFE channel on your receiver or processor to achieve the desired bass output. See your receiver or processor's owner's manual for more information. 2) The SPEAKER LEVEL jacks connect directly to the speaker outputs of any amplifier, integrated amplifier, or receiver. LOW-PASS CROSSOVER - Use this knob to select the high-frequency range at which you wish to cut-off the signal to the subwoofer. VRP User's Manual (2) (3) . (4) www. velodyne. com 5 (5) (6) (7) Power indicator - Red: Unit is in standby mode. (automatically turns to STANDBY mode if no signal for eight minutes) PHASE switch - Select the switch position at which you hear a louder bass sound. VOLUME LEVEL knob - Use this knob to adjust the output level of the subwoofer. C ro s s ov e rs Receiver/Processor Subwoofer Outputs The Velodyne subwoofer is designed to operate using the full range audio signal for input when using the built-in crossover. Many home theater processors/receivers (Dolby DigitalTM, DTSTM, THXTM) have a "subwoofer out" jack (sometimes labeled "LFE") that is internally filtered, settable at the receiver/processor, and designed to be used with a powered subwoofer. In some installations, it may be beneficial to use BOTH the Velodyne crossover and the receiver/processor crossover, resulting in a steeper ultimate crossover slope. In some rare cases, combining both an external crossover and the one internal to the subwoofer may result in low output and increased noise. In these installations you may need to bypass the crossover in either the processor or your VRP subwoofer, or simply setting one crossover to a higher frequency (such as 120 Hz) will restore maximum performance. (Refer to Figure 2a Line-Level Subwoofer Connection Diagram and Figure 2b Speaker-Level Subwoofer Connection Diagram, pages 7 and 8 for connection diagrams. ) . www. velodyne. com VRP User's Manual 6 Figure 2a. Line-Level Subwoofer Connection Diagram . www. velodyne. com VRP User's Manual 7 RIGHT FRONT SPEAKER, LEFT FRONT SPEAKER . Figure 2b. Speaker-Level Subwoofer Connection Diagram www. velodyne. com VRP User's Manual 8 Interconnect Cables When installing your new Velodyne subwoofer using the line level connections, you should always use shielded phono cables. There are many high quality cables available today. [. . . ] Date Puchased_________________________________________________________________ Dealer_________________________________________________________________________ Serial #________________________________________________________________________ *NOTE: Please complete and return your warranty card within ten (10) days or Register. and easier www. velodyne. com LIMITED WARRANTY VELODYNE ACOUSTICS, Inc. ("VELODYNE") warrants all electronics and powered subwoofers for a period of two years and full range speakers for a period of five years. All VELODYNE products have a warranty from the date of purchase against defects in materials and workmanship subject to the following conditions: 1. [. . . ]