User manual VELODYNE SC-600 IF-IC DATASHEET

[. . . ] . 4 Rear Panel Connections - Detailed Explanation . . 8 ­ A Word About Your Home Theater Receiver's Crossover and the SC-600 IF-IC IF-IC Amplifier's Crossover . . 8 ­ A Word About Interconnect Cables . . 9 ­ A Word About Subwoofer Placement . [. . . ] (18) Power Cord Adapter Connect the detachable power plug to this male interface connection. The detachable cord allows for easy replacement should the original become damaged. (19) Fuse If the unit is not functioning, check the fuse. If the fuse is blown, replace with an identically rated fuse. If the fuse blows again, refer the unit for service. (20) Main Power Switch Press the POWER switch to the ON position to activate the amplifier. If the unit is to be left unused for an extended period of time, move this switch to the OFF position to prolong the life of the amplifier. . www. velodyne. com SC-600 IF-IC IF-IC Amplifier User's Manual 7 R e a r Pa n e l C o n n e c t i o n s -- D e ta i l e d E x p l a n a t i o n The SC-600 IF-IC IF-IC amplifier is equipped with both speaker-level and line-level inputs. To do this, depress BOTH the Crossover UP and indicating that the Crossover DOWN buttons simultaneously. The numeric LED will show low-pass crossover has been defeated. To reactivate the low-pass crossover, simply push the crossover UP or crossover DOWN buttons. -- A WORD ABOUT YOUR HOME THEATER RECEIVER'S CROSSOVER AND THE SC-600 IF-IC IF-IC AMPLIFIER'S CROSSOVER Your Velodyne SC-600 IF-IC IF-IC amplifier is designed to operate using the full range audio signal for input when using the built-in crossover. Many home theater processors/receivers have a "subwoofer out" jack that performs this same function and are designed to be used with a powered subwoofer. . www. velodyne. com SC-600 IF-IC IF-IC Amplifier User's Manual 8 In these installations, you may want to bypass the crossover in either the processor or the Velodyne SC-600 IF-IC IF-IC amplifier as described above. Then, turn the switch on while depressing any of the buttons on the front panel (crossover up or down, or volume up or down). The unit will show the model it is currently controlling. To change the model, simply push the crossover up or crossover down buttons and the model changes on the LED display. Once the desired model is seen on the LED display, simply release the button. You don't need to do anything else - the model to be controlled is automatically stored in the SC-600 IF-IC IF-IC amp's memory. To exit model selection mode, use the main power switch on the back panel to power down and power up the unit. You should see the model you selected for two seconds on the LED display before the display reverts to the volume. Note: The SC-600 IF-IC IF-IC amplifier can control only one subwoofer at a time, either the SC-600 IF-IC IF-IC IW or SC-600 IF-IC IF-IC IF/IC. . www. velodyne. com SC-600 IF-IC IF-IC Amplifier User's Manual 10 Usage This section addresses EQ setup and day-to-day usage of your SC-600 IF-IC IF-IC amplifier. Remote Control The features of the SC-600 IF-IC IF-IC remote control are listed below. · POWER -- This button forces your SC-600 IF-IC IF-IC amplifier unit into standby mode. The power LED turns amber, the numeric LED shuts off, and the amplifier puts out no power. The unit will remain in this mode until the POWER button is pressed again. [. . . ] We recommend replacing the batteries in the remote. If the protection circuitry is active, the unit may cycle on and off until operating parameters return to normal. Under more serious conditions, the unit may shut off completely. Normal operation should return upon cooling, but you may be required to turn the power off and then on again to reset the unit. [. . . ]