User manual VELODYNE SPL-1000I DATASHEET

[. . . ] Please, read and follow the instructions below to insure safe and proper system operation. To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open speaker enclosure or amp chassis cover. Please observe all warnings on the equipment itself. [. . . ] Refer to your receiver manual for the individual channel level adjustment procedure. If your receiver Sub-Out channel is set too low, the subwoofer may appear to have a weak output, it may sound noisy or distorted, and the Auto On/Off feature may not operate properly. (4) Mic Input Connect the supplied microphone for the Auto-EQ feature to this mini-jack input. . www. velodyne. com SPL-Ultra User's Manual 6 R e a r Pa n e l C o n n e c t i o n s Figure 2. SPL-Ultra Rear Panel Connections Figure 2 shows the connections on the rear panel of the SPL-Ultra. RE . www. velodyne. com SPL-Ultra User's Manual 7 Following are brief descriptions of the connections described in Figure 2. More detail on these connections can be found in the next section. (1) LOW-PASS CROSSOVER Use this knob to select the frequency above which you wish to roll off the signal to the subwoofer. When the knob is turned all the way to the left, the Subwoofer Direct feature is invoked and the subwoofer plays all frequencies up to 200 Hz. (2) VOLUME Control This control allows you to balance the output from the subwoofer to the main speakers in your system. This control should be set to achieve similar volume level from between both the main speakers and subwoofer. When pressing volume up or down, set the level while watching the LED display for reference. The upper button increases the subwoofer level and the lower button decreases it. Note: If you are not using an external crossover, you should use the built-in crossover for the best performance. When using a single RCA sub out from the processor, connect to the "L" - LFE input on the subwoofer, or for more signal, use a "Y" connector and feed the signal into both "R" and "L" inputs. Interconnect Cables When installing your new Velodyne subwoofer using the line-level connections, you should always use shielded phono cables. There are many decent cables available today, most any of which will work perfectly well. We do recommend that you keep the length of cable as short as possible to avoid any potential noise problems. When using speaker level connections, use a quality speaker cable that mates well with the connectors (at least 18-gauge). Be very careful to avoid any loose or frayed strands that could result in a short, causing a dangerous condition and possible damage to your unit. Cables of extremely large size are typically not required. Extremely large gauge wire may not properly fit in the binding posts, resulting in a poor connection and possible short circuits. . www. velodyne. com USAGE SPL-Ultra User's Manual 10 Usage This section addresses day-to-day usage of your SPL-Ultra subwoofer. Remote Control Figure 3 shows the remote control, enabling you to easily choose whatever listening mode you desire. NOTE: The SPL-Ultra remote can be attached magnetically to the back of the subwoofer in the upper left hand corner. Figure 3. Remote Control POWER This button forces your SPL-Ultra unit into standby mode. The woofer will not play and the LED will turn off. [. . . ] The following conditions require service by a qualified technician: 1. The unit does not appear to operate normally or exhibits a marked change in performance 3. Some part of the chassis or circuitry is physically damaged Thank You for Purchasing a Velodyne SPL-Ultra Subwoofer! . www. velodyne. com SPL-Ultra User's Manual 15 Specifications Model Woofer: Amplifier: (Class D) High Pass Crossover: Low Pass Crossover*: SPL-800 Ultra 8" forward firing (6. 5" piston diameter) 2400 watts Dynamic 1200 watts RMS Power 80Hz (6 dB/octave) 40-135Hz SPL-1000 Ultra 10" forward firing (8" piston diameter) 2400 watts Dynamic 1200 watts RMS Power 80Hz (6 dB/octave) 40-135Hz *12 dB octave initial, 24 dB octave ultimate SPL-1200 Ultra 12" forward firing (9. 7" piston diameter) 2400 watts Dynamic 1200 watts RMS Power 80Hz (6 dB/octave) 40-135Hz Frequency Response: Overall (+/-3 dB) Harmonic Distortion: Magnet Structure: Voice Coil: Inputs: Outputs: Phase: Video Shielded: Dimensions (H/W/D): (inc. feet, grill and knobs) Cabinet: Finish: Accessories: Warranty (parts/labor): (North America) Shipping Weight (approx. ): 16-240Hz 26-135Hz <5% (typical) 204 oz. [. . . ]