User manual VELODYNE SPL-800R REV F 1

[. . . ] SPL-R Series TM SPL-800R SPL-1000R SPL-1200R SPL-1500R USER'S MANUAL DSP-Controlled Home Theater Subwoofer R e s t oo nn g D e fa u l t s Cauti ri . www. velodyne. com SPL-R User's Manual i Ta b l e o f C o n t e n t s Congratulations . . 3 Rear Panel Connections - Detailed Explanation . . 13 . www. velodyne. com SPL-R User's Manual ii Congra ng a e ons R e s t o r i t u l Dt ifa u l t s Congratulations on your purchase of a Velodyne Small Plays Loud-Remote (SPL-R) subwoofer. This system represents the state-of-the-art in low frequency reproduction. [. . . ] To bypass the subwoofer's internal crossover when the unit is being fed a low pass signal from another crossover, simply locate the switch marked "LOW-PASS CROSSOVER" on the rear panel of the subwoofer and turn it counterclockwise to the leftmost position. This will eliminate the internal crossover from the signal path. Note: If you are not using an external crossover, you should use the built-in crossover for optimal performance. When using a single RCA sub out from the processor, connect to the "L" - LFE input on the subwoofer. Interconnect Cables When installing your new Velodyne subwoofer using the line-level connections, you should always use shielded phono cables. There are many decent cables available today, most any of which will work perfectly well. We do recommend that you keep the length of cable as short as possible to avoid any potential noise problems. When using speaker level connections, use a quality speaker cable that mates well with the connectors (at least 14-gauge). Be very careful to avoid any loose or frayed strands that could result in a short, causing a dangerous condition and possible damage to your unit. Cables of extremely large size are typically not required. Extremely large gauge wire may not properly fit in the binding posts, resulting in a poor connection and possible short circuits. Placement True subwoofers operate at extremely low frequencies which are primarily omni-directional. While it is recommended that the subwoofer be placed on the same plane as the satellite speakers, room and system conditions often dictate otherwise. Keep in mind that frequency response and output level can be drastically influenced by placement, depending on the acoustic properties of the listening room. Typically, the optimum location for a subwoofer is in a front corner of your listening room. This location will usually offer the greatest output levels and optimum low frequency extension. The worst location for a subwoofer is typically far away from any walls, close to the center of your room and near an opening or doorway. When using a pair of Velodyne subwoofers in stereo, it is preferable to place each subwoofer by the satellite of the same channel. In this case, the previous EQ settings will be preserved. PHASE These buttons allow you to optimize the subwoofer performance for the location and your listening position. Select the switch position at which you hear the most bass. The light will blink according to the following schedule: 0 degrees 90 degrees 180 degrees 270 degrees 1 2 3 4 blink blinks blinks blinks LIGHT If you wish, you can deactivate the blue front panel light on your SPL-R unit. To do this, press the LIGHT button on your remote. To reactivate the light, press the LIGHT button again. NIGHT Night mode limits the maximum output of the subwoofer for later night listening or to be more considerate of close neighbors. Press the night button to turn the night mode feature on or off. [. . . ] The following conditions require service by a qualified technician: 1. The unit does not appear to operate normally or exhibits a marked change in performance 3. Some part of the chassis or circuitry is physically damaged Thank You for Purchasing an SPL-R Subwoofer! . www. velodyne. com SPL-R User's Manual 10 Specifications Specifications Woofer: Amplifier: (Class D) High Pass Crossover: Low Pass Crossover*: SPL-800R 8" forward firing (6. 5" piston diameter) 2000 watts Dynamic 1000 watts RMS Power 80Hz (6 dB/octave) 40Hz-120Hz SPL-1000R 10" forward firing (8" piston diameter) 2000 watts Dynamic 1000 watts RMS Power 80Hz (6 dB/octave) 40Hz-120Hz SPL-1200R 12" forward firing (9. 7" piston diameter) 2000 watts Dynamic 1000 watts RMS Power 80Hz (6 dB/octave) 40Hz-120Hz SPL-1500R 15" forward firing (12. 7" piston diameter) 2000 watts Dynamic 1000 watts RMS Power 80Hz (6 dB/octave) 40Hz-120Hz *12 dB octave initial, 24 dB octave ultimate Frequency Response: (+/-3 dB) Harmonic Distortion: Magnet Structure: Voice Coil: Inputs: Outputs: Phase: Video Shielded: Dimensions (H/W/D): (inc. feet, grill and knobs) Cabinet: Warranty: (parts/labor) Shipping Weight (approx. ): 28-120Hz <5% (typical) 204 oz. [. . . ]