User manual VERBATIM STORE N GO PORTABLE HARD DRIVE ESATA-USB 2.0 COMBO

[. . . ] 1 MB = 1, 000, 000 bytes / 1 GB = 1, 000, 000, 000 bytes / 1 TB = 1, 000, 000, 000, 000 bytes. Some capacity used for pre-loaded software, formatting and other functions, and thus is not available for data storage. As a result, and due to differing calculation methods, your operating systems may report as fewer megabytes/gigabytes/ terabytes. About Powered eSATA External SATA (or "eSATA") ports can transfer data at very high data rates (up to 3. 0 GB/s). However, the original eSATA specification does not provide a power connection through the standard eSATA connector. [. . . ] If you are using a USB 1. 1 port on your Windows computer, the following cautionary note may appear on your display: Hi-Speed USB Device plugged into non-Hi-Speed USB hub. This does not indicate a problem because the drive is compatible with both USB 1. 1 and USB 2. 0 ports. However, in this case the drive will operate only at USB 1. 1 speeds. Note 2: USB or eSATA under Mac OS X 10. 2. Mac OS X version 10. 2 will not mount any single FAT32-formatted (MS-DOS) partition greater than 128GB. To work around this OS limitation, you may partition the drive into smaller FAT32 partitions, or you may reformat the drive to HFS+ format. Though the eSATA interface standard provides for "hot-plugging" of the drive, some computers may not follow the standard precisely. If you find that your drive does not mount after attaching to a computer that is powered on, then shut down the computer, attach the drive, and then boot up your computer. Most computers will supply sufficient power through the USB port to operate the drive. However, if the drive does not immediately spin up and mount this may indicate that your laptop is not supplying sufficient power. In this case you may optionally apply additional power from a second USB port of your computer. To do this connect the supplied Auxiliary DC Power Cable between the computer's second USB port and the Auxiliary Power DC Input jack on the drive. Disconnecting Portable Hard Drive Your Portable Hard drive is hot-pluggable; it can be connected and disconnected without restarting your computer. To disconnect your portable hard drive at any time, simply perform the following steps. You can also disconnect your hard drive at any time while your computer is powered off. Note: Please be careful to follow the correct procedure when disconnecting your unit. Simply unplugging the unit without first following the instructions below may result in damage to your unit and/or loss of data. For Windows Users: 1 If you have files located on your drive open in any applications, close them. 2 Click the Unplug or Eject Hardware button in the System Tray. 3 Select your drive from the menu that appears. 4 After a moment, Windows will display a message that your hardware can be safely removed. For Mac OS Users: 1 If you have files located on your drive open in any applications, close them. 2 Locate the icon for your drive on the desktop, and drag it to the trash. 6 Technical Support If you are experiencing difficulty installing or using your Verbatim product, please visit the main Verbatim Technical Support website at www. verbatim-europe. com. From this page you can access our library of user documentation, read answers to frequently asked questions, and download available software updates. Although most of our customers find this content sufficient to put them back on the right track, this page also lists ways in which you can contact the Verbatim Technical Support Team directly. Europe: For technical support in Europe e-mail drivesupport@verbatimeurope. com or call 00 800 3883 2222 in the following countries: Austria, Belgium, Denmark, Finland, France, Germany, Hungary, Italy, Luxemburg, Monaco, Netherlands, Norway, Poland, Portugal, Republic of Ireland, Spain, Sweden, Switzerland and United Kingdom. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]