User manual VESTAX GE-31A

[. . . ] Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. FEATURES The GE-31A was built to give Carl Cox what he always wanted. A solid, reliable, high quality mixer, that has enough features to allow him to give 110% during every performance, every time. [. . . ] The cut off point can be adjusted by using the SWEEP volume rotary dial !1. If this switch is pressed simultaneously with the High Pass Filter switch the resulting effect is a Notch Pass Filter. !1 SWEEP VOLUME This rotary dial is used to adjust the filter cut off points on each PGM. A rotation to the left will result in a movement away from the High frequencies towards the Low frequencies. Vice versa a movement to the right will result in a movement away from the Low frequencies towards the High frequencies. !2 C. F. ASSIGN SWITCH q PHONO / LINE SELECTOR Selects the signal (PHONO or LINE) to be sent to each INPUT. Connect the output of a CD player, MD player, and tape deck to the line input. Assigns the signals from each of the PGM channels to either side of the crossfader or to MASRER OUT. There are three positions; A The PGM is sent to the "A" position or left position of the crossfader. MASTER The PGM is sent directly to the master out. B The PGM is sent to the "B" position or right side of the crossfader. w INPUT ASSIGN SWITCH Selects the input to be sent to each PGM channel. e PGM TRIM VOLUME Adjusts the input level of each PGM channel. PGM LEVEL METER to indicate at about 0dB. !3 CUE SWITCH Sends a signal from each PGM to the monitor section for headphone monitoring. (Delay, Reverb, etc. ) $1 GND TERMINAL #5 HEADPHONE EQ VOLUME Adjusts the HI and LOW frequencies for Headphone monitoring. #6 HEADPHONE LEVEL VOLUME Adjusts the headphone monitor level. Connect this terminal to the ground lead of the turntable. %0 MASTER LOOP RCV JACK This will help to reduce unnecessary noise. Connects the output terminal of an external effector. $2 INPUT LEVEL SELECT SWITCH[-10/0dB] Select the attenuation level for the input. $3 BOOTH OUT JACK [1/4' PHONE JACK (UNBALANCED), XLR JACK %2 AC IN JACK (BALANCED)] Connect the Vestax AC-20 , AC adaptor. This signal is identical to the HEADPHONE OUT signal. $4 BOOTH OUT LEVEL SELECT SWITCH Select the attenuation level for the BOOTH OUT. #7 PHONES JACK Use this jack to connect headphones. Headphones with an impedance of 8ohm to 600ohm can be used on this unit. *For best sound quality Vestax recommends using Headphones with 150ohm impedance. $5 MIC MONITOR IN/OUT SWITCH Select whether the signal connected to MAIN/SUB MIC is mixed with the signal outputted from MASTER OUT1/2. $6 REC OUT JACK Connects to the input jack of a recording device IE, tape recorder, MD, DAT, etc. The output level of this jack is fixed and does not change with the MASTER LEVEL. HOW TO CHANGE THE FADER UNIT INPUT FADER Change to "IF-500" q Remove the fader knob. (See fig-a) w Remove the 4 screws which fix the input fader panel to the mixer. (See fig-b) e Remove the 2 screws which fix the input fader. [. . . ] stand, tripod, bracket, or table recommended by the manufacturer, or sold with product. Any mounting of the appliance should follow the manufacturer's instructions, and sholud use a mounting accessory recommended by the manufacturer. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. [. . . ]