User manual VESTAX PETIT POPE

[. . . ] This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. [. . . ] Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. If liquid has been spilled or objects have fallen into the product. If the product has been exposed to rain or water. If the product dose not operate normally by following the operating instructions. Adjust only those controls that are coverd by the operating instructions as an improper adjustment of other, controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or cabinet has been damaged. When the product exhibits a distinct change in perfromance-this indicates need for service. 16. Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characterristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. Safety Check-Upon completion of any service or repairs to product, ask the service technician to perfrom sefety checks to determine that the product is in proper operating condition. High frequency range is boosted up to +4dB when this knob is rotated clockwise. When the knob is rotated counter-clockwise, high frequency range is cut off up to infinity level. For example, it can be used to emphasise or cut off the cymbals or high hats. 4 7 HI CUT (Fader type cut switch HI) When this volume is set to bottom position, high frequency range is cut of completely regardless of the position of the HI level control. The HI level control knob becomes active when this volume is set to maximum top position. HOW TO REPLACE THE INPUT FADER Remove four screws, which hold the fader unit panel. Carefully remove the multi-cable connector from the fader unit. Insert the connector to the new fader unit. Place the fader unit to proper position and fix it with four screws. 8 MID CUT (Fader type cut switch MID) When this volume is set to bottom position, mid frequency range is cut of completely regardless of the position of the MID level control. The MID level control knob becomes active when this volume is set to maximum top position. + + 9 LOW CUT (Fader type cut switch LOW) When this volume is set to bottom position, low frequency range is cut of completely regardless of the position of the LOW level control. The LOW level control knob becomes active when this volume is set to maximum top position. Remove four screws. Remove the multi-cable connector from fader unit. 10 INPUT FADER Used to adjust the input level of each program. Please replace with IF-25 when it is worn out, or with the optional rotary fader unit, RF-25, for house applications. + + MASTER SECTION 13 11 12 14 15 16 11 LED LEVEL METER The bar graph level meters indicate the master output level L channel and R channel or input level of each program program 1 and 2 . 14 MASTER (MASTER level volume) Adjusts the output level of LINE OUT and PA OUT. 15 16 BOOTH OUT Adjusts the output level of BOOTH OUT. 12 METER SELECT When this switch is set to MASTER, the bar-graph meter indicates the master output level L channel and R channel . [. . . ] It is used to prevent low frequency noise such as breathing, vibration, etc. 17 18 19 MONITOR SECTION 20 CUE SELECTOR Used to select the cue signal to be monitored by headphones from PGM1, PGM2 or AUX. 21 STEREO CUE (Stereo Cue ON/OFF Switch) When this switch is set to ON, the input signal selected by CUE SELECTOR can be monitored in stereo through headphones. When this switch is set to OFF, the master signal can be monitored through the right side of the headphone all the time, the CUE signal selected by CUE SELECTOR will be heard from the left side. This feature allows DJs to monitor current and next source simultaneously. 20 21 22 23 22 23 LEVEL (Headphone Level) Adjust the monitor level of the headphones. PHONES (Headphone Jack) Used to connect the headphones. Headphones with impedance from 8~600 can be used. 6 REAR PANEL SECTION 28 25 24 27 32 33 31 30 29 26 25 24 27 24 PHONO 1, 2 [RCA PIN JACK] Connect turntables equipped with MM (Moving Magnet type) cartridge. [. . . ]