User manual VESTAX PMC-05PRO3

[. . . ] 1 x Effects Send and 1 x Effects Double Panel. Vestax invented the double panel Receive means that you can hook up an external system in order to open up the faceplate for fast effects unit for use during play. The volume of moves and reduce personal injury (fingernails). your send and receive signal is easily controlled This full battle worthy layout was designed with a through 2 x volume knobs and the signal can be sent lot of advice from top-level scratch and to PGM1, PGM2 or both simultaneously. [. . . ] set, PGM1 will be heard with the crossfader set to the left iMASTER LEVEL VOLUME side. PGM2 will be heard with the cross fader set to the Adjusts the signal level outputs from LINE OUT. When the crossfader is set in the center, both programs will be heard. This is user replaceable fader oCROSSFADER CURVE Replace with a "CF-PCV" when it is worn out. A clockwise rotation gives a steep crossfader good for scratching and !5 EFFECT RCV LEVEL cutting, whereas, a counter clockwise rotation gives a Adjusts the signal level input from an external effects unit gentle crossfader good for long running mixes. connected to the EFFECT RCV jacks on the front panel. !0 POWER LED Lights up when the POWER SWITCH is on. !6 EFFECT SEND LEVEL Adjusts the signal level output to an external effects unit connected to the EFFECT SEND JACK on the rear panel. !1 INPUT SELECTOR !2 INPUT FADER (PGM1/PGM2) Used to select the input (LINE or PHONO) to be sent to each PGM channel. The upper most position will select PHONO input. !7 EFFECT SEND ON/OFF SWITCH This selector switch can also be used to perform for This switch is used to select the PGM to be sent to TRANSFORMER SCRATCH. The operation direction of this EFFECT SEND JACK. To change the operational direction of this !8 MONITOR LEVEL switch remove the top panel and make the necessary the top panel. Adjusts the headphone monitor level. Used to adjust the input level of each PGM channel. The Input Crossfaders signal to be monitored from each program. fader curve can be changed using a switch located on the unit @0 MONITOR SELECT SWITCH itself. Ensure that you This switch is used to select the signal sent to the monitor replace with an IF-05PCV when it is worn out. When set to CUE the signal heard is determined comprehensive instructions please refer to the "HOW TO by which PGM is being sent to the master and the location CHANGE THE FADER UNIT" section of this user guide. When set to MASTER you !3 INPUT LEVEL METER will hear the master signal in the monitor section. The LED level meters indicate the signal level of each !9 CF MONITOR FRONT PANEL @1 PHONE JACK Connect the headphones with the impedance of 8ohm to 600ohm. @3 EFFECT SEND JACK Connect to the input of the external effects. (Delay, Reverb etc) @2 EFFECT RECEIVE JACK Connect to the output of the external effects. REAR PANEL @4 SUB MIC LEVEL Adjusts the input level from SUB MIC IN. connected, the signal from the turntable is fed to the respective PGM when the Phono Input is selected. @5 MAIN/SUB MIC JACK Input jack for MAIN/SUB MIC. @8 GROUND TERMINAL Connect this terminal to the ground lead of the turntables. @6 LINE INPUT JACK @7 PHONO INPUT JACK These jacks are used to connect line level output @9 POWER JACK devices to the PMC-05proIII. Devices with a line Connect the Vestax DC-15A , AC adaptor. level of -10dB to 0db, such as CD player, MD #0 LINE OUT players, tape decks, DAT players etc. may be The PMC-05ProIII has two pairs of Line Out jacks connected to these jacks. The signal from these sending the same output signal to an external devices is then fed to the respective PGM when Line amplification device. [. . . ] Object and Liquid Entry-Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing-Do not attempt to service product yourself as opening or removing covers may expose you to dangerrous voltage or other hazards. Refer all servicing to qualified sersonnel. [. . . ]