User manual VESTAX PMC-09A

[. . . ] Any mounting of the appliance should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power sources-This product should be operated only from the type of power source indicated on the marking label. [. . . ] If the product has been exposed to rain or water. If the product dose not operate normally by following the operating instructions. Adjust only those controls that are coverd by the operating instructions as an improper adjustment of other, controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or cabinet has been damaged. When the product exhibits a distinct change in performance this indicates need for service. 16. Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. Safety Check-Upon completion of any service or repairs to product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. FEATURES 1. For knob is rotated counter-clockwise, high example, it can be used to emphasise or cut off frequency range is cut off up to infinity level. For the bass. example, it can be used to emphasise or cut off the cymbals or high hats. 4 u HI CUT (Fader type cut switch HI) When this volume is set to bottom position, high frequency range is cut of completely regardless of the position of the HI level control. The HI level control knob becomes active when this volume is set to maximum top position. o LOW CUT (Fader type cut switch LOW) When this volume is set to bottom position, low frequency range is cut of completely regardless of the position of the LOW level control. The LOW level control knob becomes active when this volume is set to maximum top position. i MID CUT (Fader type cut switch MID) When this volume is set to bottom position, mid frequency range is cut of completely regardless of the position of the MID level control. The MID level control knob becomes active when this volume is set to maximum top position. !0 INPUT FADER Used to adjust the input level of each program. Please replace with IF-250 when it is worn out, or with the optional rotary fader unit. MASTER SECTION +6 +3 +2 +1 0 -1 -2 -4 11 PRO FESSIONAL MIXING CONTROLLER -7 -10 -20 -30 POWER -30 -20 -10 -7 -4 -2 -1 0 +1 +2 +3 +6 Lch PGM 1 Rch AUX METER SELECT PGM 2 14 MASTER MIN MAX 13 PGM 12 15 MASTER BOOTH OUT 16 MIN MAX MIN MAX 17 !1 POWER INDICATOR The LED light when the power is on. !2 LED LEVEL METER The bar graph level meters indicate the master output level L channel and R channel or input level of each program program 1 and 2 . PGM 2 LEVEL 1 2 !5 MASTER (MASTER level volume) Adjusts the output level of LINE OUT and PA OUT. !3 METER SELECT !6 BOOTH OUT Adjusts the output level of BOOTH OUT. When this switch is set to MASTER, the bargraph meter indicates the master output level L !7 CROSS FADER channel and R channel . When it is set to The signal from PGM1 is output when the cross PGM, the left meter shows the input level of fader is set to the left side. The signal from PGM1 and the right meter shows the input level PGM2 is heard when the cross fader is set to of PGM2. When the cross fader is set at centre position, both programs will be mixed !4 AUX (AUX level volume) and output at the same time. [. . . ] The signal from line #1 PA OUT LEVEL (Balanced Output Level Select Switch) [-10dB/0dB] level equipment is fed to the PGM channels Used to select the output level of the PA OUT when Line input is selected. Please select the level according to the input sensitivity of the power @7 AUX IN (LINE 5, PHONO 3) [RCA PIN JACK] amplifier or the master console. Input jack for turntable and line level equipment. The signal from these jacks are fed to AUX input #2 LINE OUT (Unbalanced Output) [1/4" PHONE JACK] channel. [. . . ]