User manual VESTAX PMC-27MKII

[. . . ] Temperature Avoid use in hot, (over 35 )and cold, (boiow 5 ) locations. Keep the unit away from extreme direct heat such as direct sunlight, heating radaitors, or closed vehictes. Power cord handling Connecting the power cord to other cords or joining cords together can cause lire and electric shock. Take precaution when handling ACplugs and connectors. [. . . ] The product has been dropped, or the enclosure damaged. Do not attempt to service the product beyond that described in with its proper ventilation. The product should be located away from heat sources such as the use - maintenance instructions. All other servicing should be referred to qualified service personnel. radiators, heat registers, or other products that produce heat. The product should be connected to a power supply only of the type described in operating instructions or as marked on the product. TOP PANEL PROGRAM INPUT SECTION PRO FESSIONAL MIXING CONTROLLER LINE 4 IN L R INPUT PHONO 1 PGM 1 INPUT LINE 2 PHONO 2 SUB INPUT LINE 4 PHONO 3 PGM 2 LINE 6 MASTER +8 +5 +3 +8 +5 +3 +1 0 -1 -3 -5 -7 -10 -15 POWER CUE MIC TRIM LINE 1 LINE 3 LINE 5 MASTER SECTION +1 0 TRIM TRIM -1 -3 MIC-1 MIC-1 MIC-2 MIN MAX MIN MAX MIN MAX -5 -7 -10 -15 BAL BAL BAL MICROPHONE SUB INPUT SECTION MIN MAX L R L R L R POWER MIC-2 EQ HI EQ HI EQ HI L R EFFECT SEND MIN MAX EQ HI -16dB +16dB -16dB +16dB -16dB +16dB MID MID MID MIN MAX RETURN -16dB +16dB -12dB +12dB -12dB +12dB -12dB +12dB LOW LOW LOW LOW MIN MAX CUE -16dB +16dB -16dB +16dB -16dB +16dB -16dB +16dB EFFECT OFF POST EFFECT PRE OFF POST EFFECT PRE OFF POST EFFECT PRE OFF POST OFF ON MASTER BAL CUE OFF ON CUE OFF SIGNAL ON CUE OFF SIGNAL ON CUE OFF SIGNAL ON L R LEVEL 10 9 8 7 6 5 4 3 2 1 0 10 9 8 7 6 5 4 3 2 1 0 10 9 8 7 6 5 4 3 2 1 0 MIN MAX MONITOR SPLIT CUE ON OFF PHONES LEVEL MIN MAX PHONES IN PGM1 ISOLATOR PGM2 ISOLATOR LOW MID HI 1 2 LOW MID HI ISOLATOR SECTION PHONES IN PROGRAM INPUT SECTION PGM 1 INPUT PHONO 1 PROGRAM INPUT SECTION 1. INPUT SELECTOR Used to select input (2line or 1phono) to be sent to each PGM channel. TRIM CONTROL Adjusts the Input level of each channel. adjust TRIM so that the INPUT LEVEL METER shows about 0dB. BALANCE CONTROL Adjusts the stereo balance for each PGM channel. Can be used for adjusting the unbalanced stereo image caused by a strong anti-skating setting. Clockwise rotation from center position Increases the volume of R over L channel. A counter clockwise rotation Increases the volume of L channel over R. EQUALIZER(HI, MID, LOW) Adjusts the HI, MID, LOW frequencies for each PGM channel. HI 8kHz 12dB Shelving type MID 500Hz 16dB Peaking type LOW 80Hz 12dB Shelving type 5. EFFECT SWITCH This switch enables the signal from each programs to be sent to AUX send jack. Different signal routes can be selected this switch to different positions. P R E : The signal before the input fader ( after the EQ ) will be sent to AUX output. POST : The signal after the input and cross fader will be sent to AUX output. O F F : No signal will be sent to AUX output. [. . . ] MASTER BALANCE VOLUME Adjusts the signal balance of left to the right side of the outputs from the OUTPUT jack on the rear panel. MASTER LEVEL VOLUME Adjust the signal level output from the OUT PUT jack on the rear panel. SPLIT CUE SWITCH When this switch is ON, the master signal is always heard through the right earcup of the headphone. The CUE signal will be heard in the left earcup when that input is selected by the CUE SWITCH (5, 14). [. . . ]