User manual VESTAX PMC-500

[. . . ] Accessories-Do not place this product on an unstable cart, stand, tripod, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. stand, tripod, bracket, or table recommended by the manufacturer, or sold with product. [. . . ] Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. SPECIFICATION FEATURES FUNCTIONS PROGRAM INPUT SECTION NOTE oPGM TRIM Adjusts the input level of each PGM channels. For acoustic clarity, set the INPUT FADER and MASRER FADER to a position of 7-8. Then adjusts the INPUT LEVEL METER !7 so as to established an indicated level of about 0dB. !0 PGM ISOLATOR HI Adjusts the HI frequency level of each PGM. !1 ISOLATOR MID Adjusts the MID frequency level of each PGM. !2 PGM ISOLATOR LOW Adjusts the LOW frequency level of each PGM. qLINE INPUT RCA JACK Input connectors for line level equipment such as CD players, MD players, tape decks, DAT and VTR etc. !3 AUX SEND SWITCH This switch enables the signal from each program to be sent to AUX SEND JACK $9. This signal can be sent to the AUX device in the following three (3) ways; PRE: The signal before the input fader (after EQ) will be sent to AUX SEND JACK. POST: The signal after the input fader and crossfader will be sent to AUX SEND JACK. OFF: No signal will be sent to AUX SEND JACK. wMIC EQ (HI/LOW) Adjusts the HI and LOW frequencies for the MIC input. eMIC LEVEL Adjusts the input level of the MIC input. rMIC/LINE SELECT SWITCH Selects between MIC and LINE input. !4 C. F. ASSIGN SWITCH Assigns the signals from each of the PGM channels to either side of the crossfader or to MASTER OUT. There are three positions; A The PGM is sent to the "A" position or left position of the crossfader. MASTER The PGM is sent directly to the master out. B The PGM is sent to the "B" position or right side of the crossfader. tMIC/LINE CUE LED When MIC is selected this LED will be illuminated. yMIC/LINE CUE ON/OFF SWITCH Sends the signal from the mic channel to the monitor section for headphone monitoring. uMIC/LINE CUE LED When CUE is selected this LED will be illuminated. iINPUT SELECT SWITCH !5 CUE ON/OFF SWITCH Sends a signal from each PGM to the monitor section for Selects the input to be sent to each PGM channel. the five (5) main PGMs you can select from up to three !6 CUE LED (3) input sources as follows. This LED will be illuminated when the CUE PGM-1 PHONO1/LINE1/LINE2 SWITCH !5 is on. PGM-2 PHONO2/LINE3/LINE4 !7 INPUT LEVEL METER PGM-3 PHONO3/LINE5/LINE6 The LED bar level meters indicate the L and R outputs. PGM-4 PHONO4/LINE7/LINE8 PGM-5 PHONO5/LINE9/LINE10 !8 INPUT FADER All phono inputs are RIAA equalized. The line inputs Adjusts the Input level of each program. Typically this can be assigned to either a CD player, MD player, DAT fader is set to a position of 7-8. [. . . ] These jacks are Phone type for consumer applications. This mixer has two sets of MASTER OUT jacks so that the each output level can be set separately. Therefore, the MASTER OUT can be used for main output or sub output IE. [. . . ]