User manual VIEWSONIC PJD6230

[. . . ] PJD6220/PJD6230/PJD6240 DLP Projector ViewSonic ® - User Guide - Guide de l'utilisateur - Bedienungsanleitung - Guía del usuario - Guida dell'utente - Guia do usuário - Användarhandbok - Käyttöopas - - () IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://www. viewsonic. com in English, or in specific languages using the Regional selection box in the upper right corner of our website. "Antes de operar su equipo lea cuidadosamente las instrucciones en este manual" - () Model No. : VS11949 VS11986 VS11990 Compliance Information FCC Statement This device complies with part 15 of FCC Rules. [. . . ] Connect the other end of the internet cable to an available LAN connector on the RJ45 outlet. Make sure the PC/NB is also connected to the internet. There are two ways to connect to the network control: A. Enable DHCP from the projector OSD, under Network Config. 2. Please wait for the PC server to release IP address to the projector. DHCP icon will pop up on the bottom right corner, once the IP address is received by the projector. Enter "Given IP address (For example http://10. 0. 50. 100/)" into the address bar of the web browser and press "Enter" key or click "Go" button. From your computer, go to Start > Control Panel > Network Connection and right click to select Properties. ViewSonic 19 PJD6220/PJD6230/PJD6240 2. Select "Intel Protocol (TCP/IP)" and click "Properties". 3. Set your IP address on your computer, and click OK. Click "Use the following IP address" IP address: 10. 0. 50. 105, (set the last number different to the projector IP address). Subnet mask: 255. 255. 0. 0 ViewSonic 20 PJD6220/PJD6230/PJD6240 4. Enter "http://10. 0. 50. 100/" into the address bar of the web browser and press "Enter" key or click "Go" button. 5. After the connection is completed, the control screen will be as below Authority on the network control of Administrator & User: Item Status Date & Time Setting Control Panel Network Alert Setting Schedule Description Show current projector status and network configuration settings. Network configuration & Password setup. Show and setup Scheduling configurations. Administrator User × × × × ViewSonic 21 PJD6220/PJD6230/PJD6240 Login Enter "http://10. 0. 50. 100/" into the address bar of the web browser and press "Enter" key or click "Go" button. If the administrative and user password is disabled, it will directly go into the Status page. If the Administrative & User password is enabled Select your User Name and enter password to login. ViewSonic 22 PJD6220/PJD6230/PJD6240 Status Information: All screen images in this manual are shown when you login with the Administrator ID. The image will differ if you login with User ID. Item IP Address Group Name Projector Name System Status Input Source Lamp Hours Filter Hours Projector Status Date(y/m/d) Time Description Show current IP address. Show if projector is Power On or Inactive *. Show lamp used hours on current projector. [. . . ] Round trip transportation costs for in-warranty products will be paid by ViewSonic. Limitation of implied warranties: There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose. Exclusion of damages: ViewSonic's liability is limited to the cost of repair or replacement of the product. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages. [. . . ]