User manual VIEWSONIC PJD6240

[. . . ] ViewSonic DLP Projector PJD6220 PJD6220-3D PJD6230 PJD6240 ® - User Guide - Guide de l'utilisateur - Bedienungsanleitung - Guía del usuario - Guida dell'utente - Guia do usuário - Användarhandbok - Käyttöopas IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found - using the Regional selection box in the upper right corner of our website. "Antes de operar su equipo lea cuidadosamente las instrucciones en este manual" Model No. : VS11949 VS11986 VS11990 Notes on the AC Power Cord AC Power Cord must meet the requirement of countries where you use this projector. [. . . ] Screen Capture Capture the current projection screen as a start-up screen. When the password function is added, image projection requires an entry of the preset password at power-on. DCR (Dynamic Contrast Ratio) Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable DCR will resume to normal contrast performance. DCR will impact lamp life and system noise performance. Closed Caption (Video and S-Video sources only) Enable or Disable closed captions by selecting CC1 (closed caption 1, the most common channel), CC2 or OFF. ViewSonic 18 PJD6220/PJD6220-3D PJD6230/PJD6240 Network Control Select either RS232 or LAN for network control. If RS232 is selected, user will not able to control the projector via LAN network and vice versa. Network Config DHCP Enable: Assign an IP address to the projector from the DHCP server automatically. Gateway Select the default gateway of the network connected to the projector. Language (Computer / Video Mode) Select the language used by the on-screen menu. Factory Default (Computer / Video Mode) Restore all menu settings to factory default settings. ViewSonic 19 PJD6220/PJD6220-3D PJD6230/PJD6240 Network Control This feature provides the ability to remotely control and manage the projector through the network. Note: 1024x768 viewing resolution is recommended. Connect one end of the internet cable to the LAN connector on projector. Connect the other end of the internet cable to an available LAN connector on the RJ45 outlet. Make sure the PC/NB is also connected to the internet. There are two ways to connect to the network control: A. Please wait for the PC server to release IP address to the projector. DHCP icon will pop up on the bottom right corner, once the IP address is received by the projector. Enter "Given IP address (For example http://10. 0. 50. 100/)" into the address bar of the web browser and press "Enter" key or click "Go" button. From your computer, go to Start > Control Panel > Network Connection and right click to select Properties. ViewSonic 20 PJD6220/PJD6220-3D PJD6230/PJD6240 2. Select "Intel Protocol (TCP/IP)" and click "Properties". 3. Set your IP address on your computer, and click OK. "Use the following IP address" IP address: 10. 0. 50. 105, (set the last number different to the projector IP address). Subnet mask: 255. 255. 0. 0 ViewSonic 21 PJD6220/PJD6220-3D PJD6230/PJD6240 4. Enter "http://10. 0. 50. 100/" into the address bar of the web browser and press "Enter" key or click "Go" button. 5. [. . . ] Take or ship the product in the original container packaging to an authorized ViewSonic service center. Round trip transportation costs for in-warranty products will be paid by ViewSonic. Limitation of implied warranties: There are no warranties, express or implied, which extend beyond the description contained herein including Exclusion of damages: ViewSonic's liability is limited to the cost of repair or replacement of the product. Damage to other property caused by any defects in the product, damages based upon inconvenience, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages. [. . . ]