User manual VISONIC CLIP DATASHEET

[. . . ] Menus and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 A The Settings You Need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 B. 1 Entering the User Settings Menu & Selecting a Setting Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 B. 2 Returning to the Previous Step or Exiting the USER SETTINGS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 15 B. 3 Buttons used for Navigation & Setting . . . 15 C. 1 Setting the Zone Bypass Scheme. . . . . . . . . . [. . . ] Before you delete a keyfob, identify the keyfob either by the keyfob No. , for example, K06, or by the ID number of the keyfob that appears on the display, and then make sure that it is the keyfob you wish to delete. If you regret and wish to abort the procedure, press the Pre-Enrollment Procedure: button. 6 7 Step 4b enables you to register the device ID and to complete the programming process without being in possession of the device itself (can also be performed off-site by the installer). Enrollment can then be completed at a later stage by following the same enrollment procedure described in Step 3 without entering the User Settings menu. 8 You can now delete another keyfob, select another option in the User Setting menu (see section B. 1 and section B. 2), or quit programming (see section B. 3). 22 D-302757 MENUS AND FUNCTIONS C. 6 Setting the Time & Time Format Here you can program or adjust the built-in-clock to show the correct time in the desired time format. You can select between a 24 hour and a 12 hour (AM/PM) time format. Carefully read the section titled "Additional Information" according to the indicated references1 etc ­ see table at end of this section. TIME & FORMAT Enter the USER SETTINGS menu and select the [TIME & FORMAT] option button to confirm. 1 and press the The display shows the currently selected time format. 2 or button until the display shows the desired time Click the to confirm . format, for example, "US FORMAT-12H" and press 2. EU FORMAT-24H or US FORMAT-12H 3. TIME 08:55A Return to step 2 TIME 12:40P Use the numerical keypad to enter the correct time, for example, "08:55 AM" at the position of the blinking cursor. 4 When you are satisfied with the setting, press to confirm. This setting can be performed only after completing steps 1 ­ 3 of section C. 7A. or button. 4 5 6 7 24 D-302757 MENUS AND FUNCTIONS C. 8 Enabling / Disabling Auto-Arming The PowerMaster-10 system can be programmed to automatically arm itself on a daily basis at a predetermined time. This feature is useful especially in commercial applications, such as in stores, to ensure that the system is always armed and without having to assign security codes to employees. Here you can enable (activate) and disable (stop) the Auto-Arming. To set the Auto-Arming time ­ see section C. 9. Carefully read the section titled "Additional Information" according to the indicated references1 etc ­ see table at end of this section. Enter the USER SETTINGS menu, select the [AUTO-ARM ENABLE] option button to confirm. 1 and press the The display shows the currently selected setting. 2 Click the or button until the display reads the desired setting, for example, "enable autoarm" and press to confirm. The display confirms the saved setting, then returns to the User Setting menu, step 1. 5 3 AUTO-ARM ENABLE 2. disable autoarm or enable autoarm 3. Return to step 1 C. 9 Setting the Auto-Arming Time Here you can program the exact time of the Auto-Arming. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this sensor does cause such interference, which can be verified by turning the sensor off and on, the user is encouraged to eliminate the interference by one or more of the following measures: ­ Re-orient or re-locate the receiving antenna. ­ Increase the distance between the sensor and the receiver. ­ Connect the sensor to an outlet on a circuit different from the one which supplies power to the receiver. [. . . ]