User manual VISONIC CLIP 4N DATASHEET

[. . . ] PROGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4. 1 General Guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4. 2 Entering the Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . 11 4. 2. 1 Programming User Settings . . . . . . . . . . . . . . . . . . 11 4. 3 Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4. 4 Permissions and User Codes. . . . . . . . . . . . . . . . . . . . . 12 4. 4. 1 Setting a New Installer Code. . . . . . . . . . . . . . . . . 12 4. 4. 2 Setting the Master Installer Code . . . . . . . . . 13 4. 4. 3 Setting User Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4. 4. 4 Enabling User Permit for Installer Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4. 4. 5 Configuring Permissions for System Reset after Alarm Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4. 4. 6 Configuring a Duress Code. . . . . . . . . . . . . . . . . . . 15 4. 5 Zones / Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4. 5. 1 General Guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 D-302756 4. 5. 2 Adding a Wireless Device. . . . . . . . . . . . . . . . . . . . . 16 4. 5. 3 Adding Wired Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4. 5. 4 Deleting a Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4. 5. 5 Modifying a Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] REPORT TO PRVT or Select between "disable report", "all", "all (-op/cl)", "all(alerts)", "alarms", "alerts" and "op/cl". D-302756 39 You can now press the REPORT" menu, or press the button to take you to the "VOICE button to take you to "<OK> TO EXIT". C. To Configure Event Types to be Reported to User 8. Enter the first private telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private. 12. Enter the second private telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private. 16. Enter the third private telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private. 20. Enter the fourth private telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private. 24. 40 D-302756 Here you determine the number of times the communicator will dial the called party's number (private telephone). 3 attempts 27. or Select between "1 attempt", "2 attempts", "3 attempts" and "4 attempts". A maximum of 2 dialing attempts is permitted by the Australian Telecommunication Authority. 28. acknowledge Here you determine whether the system will use the single acknowledge or the all acknowledge mode when reporting to private telephones. Note: In the single acknowledge mode, receiving an acknowledge signal from a single telephone is sufficient to consider the current event closed and call off the communication session. The zone will be reactivated upon disarming, or 48 hours after having been bypassed (if the system remains armed). Available options are: shut after 1 (default), shut after 2 (default in USA), shut after 3 and no shutdown. 13:SWINGER STOP You can now press the or menu in "DEFINE PANEL" or press the button to program any other button to take you to "<OK> or Select between "shut after 1", "shut after 2", "shut after 3" and "no shutdown". Repeat steps 1 to 4 of section 4. 2 "Entering the Installer Menu". TO EXIT". 4. 8. 3 Enable Monitoring of Activity at Home Here you determine the time limit for reception of signals from sensors used to monitor the activity of sick, elderly or disabled people. If no sensor detects and reports movement at least once within the defined time limit, a "not-active" alert is initiated. Options: 3, 6, 12, 24, 48, 72 hours and no act disable (default). To Configure Monitoring of Activity at Home 1. D-302756 or 43 Repeat steps 1 to 4 of section 4. 2 "Entering the Installer Menu". 21:NOT ACTIVE 4. 21:NOT ACTIVE You can now press the or menu in "DEFINE PANEL" or press the button to program any other button to take you to "<OK> or Select between "no act disable", "3 h", "6 h", "12 h", "24 h", "48 h", and "72 h". TO EXIT". 4. 8. 4 Configuring Alarm Cancel Period Here you determine the "cancel alarm" period that starts upon reporting an alarm to the Monitoring Station. If the user disarms the system within that time period, a "cancel alarm" message is sent to the Monitoring Station. Available options are: cancel time 1 m, cancel time 5 m (default), cancel time 15 m, cancel time 60 m, cancel time 4 hours and also cancel inactive (default in USA). [. . . ] THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION. However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy against the Manufacturer. When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and he recognizes having been informed of. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these limitations may not apply under certain circumstances. [. . . ]