Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual VISONIC SR-730 PG2. We hope that this VISONIC SR-730 PG2 user guide will be useful to you.
Lastmanuals help download the user guide VISONIC SR-730 PG2.
You may also download the following manuals related to this product:
VISONIC SR-730 PG2 DATASHEET (176 ko)
Manual abstract: user guide VISONIC SR-730 PG2
Detailed instructions for use are in the User's Guide.
[. . . ] · Power Supply Options: Non-rechargeable battery. Optional two non-rechargeable batteries. · Sound Types: Burglar (between 1400Hz - 3200Hz), fire, gas/Co and flood. · Entry/Exit: Exit delay beeps sound once the user has armed the system. [. . . ] Changes or modifications not expressly approved by Visonic Ltd. could void the user's authority to operate the equipment.
3. INSTALLATION
A A A A
B
1
2
3
4
5
6
G
a b
I
E F
220/110 VAC
H
9VAC 9VAC
7
C D
8
J
1. Using Philips screwdriver, remove screw and remove cover. Optional step: Hang back unit with a screw on mounting surface to make the next step (drilling marking) easier. Release catch (A) and open battery cover (B). Connect battery / optional battery and 9VAC power to the proper connectors and set the optional jumpers as desired. Optional second battery and its connector. When external power is used, set the AC Enable (ON) / Disable (OFF) jumper to Enable position (see step 8). Note: There are SR-730 PG2 model variations that are supplied with battery only, or, with battery and AC adaptor. Figure 3: Installation
2
D-302414
4. ENROLLMENT
Refer to the PowerMaster-10 Installer Guide for the device enrollment procedure.
5. MODIFY DEVICE SETTINGS
This section describes how to configure the parameters of the siren from the PowerMaster-10 control panel. To Modify the Siren Device Settings Refer to the PowerMaster-10 Installer Guide and perform the procedure for Adding A Wireless Device (section 4. 5. 2), or, Modifying a Device (section 4. 5. 5). Then continue below to modify the device settings. AC POWER Connect Here you determine whether or not to report a power failure and restore. or Select between "Disabled", and "Enabled". Here you determine whether or not the LED will be activated to indicate that the siren is operating. or Select between "Volume HIGH", "Volume LOW" and "Volume MID". Here you determine the volume level of the sounder. or Select between "Disabled", "Sounder only" and "Sounder+strobe". Here you determine whether or not to activate the squawk, and if enabled, whether to activate the sounder only, or, the sounder and strobe simultaneously. [. . . ] (ISRAEL): P. O. B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788 VISONIC INC. (U. S. A. ): 65 WEST DUDLEY TOWN ROAD, BLOOMFIELD CT. (UK): UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES MK10 0BZ. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE VISONIC SR-730 PG2
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual VISONIC SR-730 PG2 will begin.
VISONIC SR-730 PG2 DATASHEET (176 ko)
