User manual VOCE V3MAN12

[. . . ] 1-3 Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 MIDI Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 1/4-Inch Audio Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 9-Volt AC Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Value Range ( 00 - 63 ) Actual Value: 00 = Softest, 63 = Loudest 27 Percussion Volume (control switch on) - selects the percussion volume to be used when the Percussion Volume Select control switch is deactivated. Value Range ( 00 - 63 ) Actual Value: 00 = Softest, 63 = Loudest 28 Percussion Decay (control switch off) - selects the percussion decay time to be used when the Percussion Decay Select control switch is deactivated. Value Range ( 01 - 05 ) Actual Value: 01 = longest, 05 = shortest 29 Percussion Decay (control switch on) - selects the percussion decay time to be used when the Percussion Decay Select control switch is activated. Value Range ( 01 - 05 ) Actual Value: 01 = longest, 05 = shortest 30 Audio Channel Assignment - selects 1 of 4 possible audio output modes. Value Range ( 01 - 04 ) Actual Value: 01 = Audio Ch. 2, 03 = Mono, 04 = Stereo 2-8 DMI-64 Mark II User's Manual PROGRAMMING THE DMI-64 MARK II Parameter Information (cont. ) 31 Split Note- determines the MIDI note number at which the channel split point will occur, below this note the alternate preset will be active. Value Range ( 00 - 99 ) Actual Value: 00 = no split, ( 1 - 99 ) = MIDI note # 32 Alternate Preset - preset to be active simultaneously when channel split mode is in use. Value Range ( 01 - 99 ) Actual Value: ( 1 - 99 ) 33 Volume MIDI Control Switch # - MIDI controller assignment for MIDI Volume Control. Value Range ( 00 - 99 ) Actual Value: 99 = Channel Pressure, (0 - 98) = MIDI Control # 34 Rotating Speaker MIDI Control Switch # - MIDI controller assignment for Rotating Speaker On control switch. Value Range ( 00 - 99 ) Actual Value: 99 = Channel Pressure, (0 - 98) = MIDI Control # 35 Vibrato MIDI Control Switch #- MIDI controller assignment for Vibrato On control switch. Value Range ( 00 - 99 ) Actual Value: 99 = Channel Pressure, (0 - 98) = MIDI Control # 36 Chorus MIDI Control Switch #- MIDI controller assignment for Chorus On control switch. * Value Range ( 00 - 08 ) Actual Value: ( 0 - 8 ) 50 Waveform Generation Harmonic 8 - corresponds to the 6th drawbar of a tone-wheel organ. * Value Range ( 00 - 08 ) Actual Value: ( 0 - 8 ) 2-11 PROGRAMMING THE DMI-64 MARK II Parameter Information (cont. ) 51 Waveform Generation Harmonic 10- corresponds to the 7th drawbar of a tone-wheel organ. * Value Range ( 00 - 08 ) Actual Value: ( 0 - 8 ) 52 Waveform Generation Harmonic 12- corresponds to the 8th drawbar of a tone-wheel organ. * Value Range ( 00 - 08 ) Actual Value: ( 0 - 8 ) 53 Waveform Generation Harmonic 16- corresponds to the 9th drawbar of a tone-wheel organ. * Value Range ( 00 - 08 ) Actual Value: ( 0 - 8 ) 54 Copy From Preset # - used by the copy function to overwrite the current preset with data from the selected preset. * Value Range ( 01 - 99 ) Actual Value: ( 1 - 99 ) 55 Copy From Execute - activates the Copy function, overwriting the current preset with data from the selected preset (parameter 54). * Value Range ( 00 - 03 ) 03 = Do Copy Function 56 Send MIDI Patch Dump - dumps MIDI System Exclusive data corresponding to the selected preset through the MIDI OUT port. Parameters 2 through and including 43 or parameters 2 through and including 53 if a programmable waveform ( # 56 - 63 ) is selected are sent. * Activated by Value Increment button 57 Send MIDI Sample Dump - dumps MIDI Sample Dump data correspond ing to the selected waveform through the MIDI OUT port. * Activated by Value Increment button 58 Send MIDI Sample Dump Request - sends a MIDI Sample Dump Request corresponding to the selected waveform through the MIDI OUT port if the selected waveform ( parameter 3 ) is a programmable waveform ( # 56 - 63 ). If parameter 3 is not set to 56 - 63 the dump request is not sent. [. . . ] Assuming the DMI-64 II's front panel is facing you, you will notice the battery holder, containing a "coin" type Lithium battery, on the front left hand corner of the DMI-64 II's printed circuit board. Remove the battery by lifting one end of the battery retaining clip with one hand while at the same time sliding it out of the holder with the other hand. Step 4: Insert the new battery in the reverse order of Step 3 making sure that the positive side of the battery is up. Step 5: Replace top panel and refasten the screws. [. . . ]