User manual VOLTA 4560 GRAPHITE GREY

[. . . ] 7 PRODUCT LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 BACK LABEL 5 6 7 8 9 SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4560 GRAPHITE GREY PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SETUP LAN, WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] • IP Subnet Mask: The default is 255. 0. 0. 0. It allows you to set the router to act in “AP”, “Client” or “WDS” mode. The SSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging of two co-located WLANs. The default SSID of the router is “default”. Do not modify default value if you don’t know what it is, default setting is ‘Auto 20/40 MHz’. Select the upper band or lower band for your radio frequency. While upper band is selected, the channel number you can select is from channel 5 to channel 11. While lower band is selected, the channel number you can select is from channel 1 to channel 7. It is the radio channel used by the wireless LAN. All devices in the same wireless LAN should use the same channel. When “WEP64Bits” is selected, you have to enter exactly 5 ASCII characters (“a-z” and “0-9”) or 10 hexadecimal digits ("0-9", "a-f") for each Key (1-4). When “WEP-128Bits” is selected, you have to enter exactly 13 ASCII characters (“a-z” and “0-9”) or 26 hexadecimal digits ("0-9", "a-f") for each Key (1-4). There are two types of authentication mode for WPA. Enterprise (RADIUS) – It uses an external RADIUS server to perform user authentication. To use RADIUS, enter the IP address of the RADIUS server, the RADIUS port (default is 1812) and the shared secret from the RADIUS server. Please refer to “Authentication RADIUS Server” setting below for RADIUS setting. Personal (Pre-Shared Key) – Pre-Shared Key authentication is based on a shared secret that is known only by the parties involved. To use WPA Pre-Shared Key, select key format and enter a password in the “Pre-Shared Key Format” and “Pre-Shared Key” setting respectively. Pre-Shared Key You may select to select Passphrase (alphanumeric format) or Format Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the Pre-shared Key. For example: Passphrase: ”iamguest” Hexadecimal Digits: “12345abcde” Pre-Shared Key Please enter 8-63 characters as the “Pre-Shared Key”. Authentication Enter the port (default is 1812), the IP address and the RADIUS Server password of external RADIUS server are specified here. When you finish, click ‘save’ to save the settings made and restart the router so the settings will take effect after it reboots. Wireless ACL This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network. Parameter Active Actions Description Choose to either Enable – Enabled the Wireless Access Control Disable – Disable the Wireless Access Control Allow – Only allow the wireless clients with the MAC Address you have specified can access to the router. [. . . ] • Src port: This Port or Port Ranges defines the port allowed to be used by the Remote/WAN to connect to the application. It is recommended that this option be configured by an advanced user. • Dest Port: This is the Port or Port Ranges that defines the application. • Protocol: It is the packet protocol type used by the application, select either TCP or UDP or ICMP Application filter Here you can choose which applications should be blocked or allowed access. Choose which application should be allowed or denied access and click ‘Save’ to apply the settings. [. . . ]