User manual VTECH GZ 2404

[. . . ] Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use this product near water (for example, near a bath tub, kitchen sink or swimming pool). [. . . ] For best results use a VTech 2. 5mm headset. To purchase a Headset, call VTech Customer Service at 1-800-595-9511. Basic Operation Once you have a compatible 2. 5mm Headset, locate the Headset Jack on the gz 2404 Handset. Connect the plug on the Headset cord to the jack (under a small rubber flap) on the cordless Handset. Do not force the connection. NOTE: Whenever a compatible Headset is connected to the cordless Handset, the microphone on the Handset will be muted. This is done to limit the effect of background noise. Belt Clip The gz 2404 is also equipped with a detachable belt clip. Align the pins on the inside edge of the clip with the notches on the sides of the Handset. The belt clip should snap securely into place. Do not force the connection. 16 In Case Of Difficulty If you have difficulties in operating your phone, the suggestions below should solve the problem. If you still have difficulties after trying these suggestions, call VTECH Communications at 1-800-595-9511. In Canada, call VTECH Telecommunications Canada Ltd. at 1-800-267-7377. The Phone Doesn't Work At All · Make sure the Power Cord is plugged in. · Make sure the telephone line cord is plugged firmly into the Base Unit and the telephone wall jack. · Make sure the battery pack is properly charged. If you get a LOW BATTERY message or indication, the battery pack needs charging. No Dial Tone · First check all the suggestions above. · If you still don't hear a dial tone, disconnect the Base Unit from the telephone jack and connect a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Contact your local telephone company. You Get Noise, Static, Or A Weak Signal Even When You're Near The Base Unit · Household appliances plugged into the same circuit as the Base Unit can sometimes cause interference. Try to move the appliance or the Base Unit to another outlet. You Get Noise, Static, Or A Weak Signal When You're Away From The Base Unit · You may be out of range. Either move closer to the Base, or relocate the Base Unit. · The layout of your home may be limiting the range. Try to move the Base Unit to another position. The Handset Does Not Ring When You Receive A Call · Make sure you have the ringers activated. Refer to the section on Set Handset Ringer Style/ Battery Save on page 8 in this User's Manual. [. . . ] 9 Display Screen Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Telephone Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Store a Number/Name in the Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Edit a Number/Name Stored in the Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]