User manual VTECH VT 650

[. . . ] We recommend that the telephone cord and mains plug be removed from your VT650 during such weather conditions. The VT650 will produce a certain amount of heat during operation. For this reason it is recommended that this equipment is NOT placed in direct contact with antique, veneered or delicate furniture surfaces. This equipment is not suitable for use in damp or humid conditions such as bathrooms. [. . . ] · The power of the signal depends on the position of the base. An upstairs room near to the centre of the house is preferred. Buildings with thick internal and external walls may impair transmission of signals to and from the base. WALL MOUNTING: Remove the handset from the base station. Clip on the supplied bracket and ensure that the fixing screws and plugs are secure before attempting to mount the base station to them. Once mounted check that the base station is stable and replace the handset. Power Supply Telephone Line 81 mm CONNECTING THE BASE STATION: Plug the lead from the adapter into the correct socket on the base unit. Plug the power adapter into a convenient 13 AMP power socket. The base is now ready to receive the handset with the batteries for charging. Charge for at least 12 hours BEFORE you attempt to connect your telephone to the telephone line. Wall Mounts Wall Mounts VT650 User Guide A/W 30/5/02 2:07 pm Page 9 8 Your Phone At A Glance 9 IN USE Lights up when handset in use TALK MEM CHN VT650 CLOCK IN USE Dial / Answer / To Seize Line Memory Channel Selection High Volume Number Recall Number Redial Tone Selection Handset Page ANS. ON/OFF TONE BATTERY TALK MEM CHN POWER IN USE CHARGE 1 4GHI 7PQRS TONE 2ABC 5JKL 8TUV 0OPER REDIAL 3DEF 6MNO PLAY STOP PLAY/STOP DEL. RECALL REDIAL RINGER 2-WAY REC. MEMO OGM1 OGM2 9WXYZ # RINGER VOL + RECALL PAGE VOL - MIC PAGE 2WAY REC Two way recording MEMO OGM1 Memo Outgoing Message 1 Outgoing Message 2 Study the illustration to ensure you are familiar with the function and position of the buttons and keys. OGM2 VT650 User Guide A/W 30/5/02 2:07 pm Page 11 10 Inserting Batteries and Charging Handset 11 HANDSET BATTERY PACK: Before using your VT650 telephone, the handset battery pack has to be installed and fully charged. The base station must be connected to the mains electricity supply using the power adapter. INSTALLING BATTERY PACK: Battery Pack INSTALLING THE HANDSET BATTERY PACK: Install the battery pack, first connect the plug on the lead to the socket and lay the battery as per diagram, fit the battery compartment door. Use only a VTech approved rechargeable battery pack. Failure to do so could result in batteries exploding whilst being charged and void the warranty. BATTERY LOW WARNING: CHARGING THE HANDSET: Place the handset on the base and leave until the handset battery pack is fully charged (at least 12 hours). The charge LED on the base will light up whilst the handset is on base. The telephone is now ready for connection to the telephone network. When the phone is in standby mode, if you see the in use LED flashing, it means that the battery is low and you need to replace your handset on the base station to recharge. · When the phone is off the hook, if the battery is low, you will hear battery low warning tone every 2 seconds. The line will disconnect after 90 seconds. · When there is an incoming call, it will have a warning beep every 2 seconds the line will disconnect after 90 seconds. OUT OF RANGE WARNING: When handset moved beyond operation range, an out of range warning tone will sound. Handset and base station will on hook automatically after 20 seconds if out of range condition persists. WARNING: Your base must be connected to the electricity supply at ALL times, except when the product is not to be used for long periods of time. VT650 User Guide A/W 30/5/02 2:07 pm Page 13 12 Making & Receiving Calls Last Number Redial & Recall 13 MAKING A CALL: Press the TALK button IN USE will light up LAST NUMBER REDIAL: Press the TALK button IN USE will light up Now dial the required telephone number. REDIAL to dial last number called. TALK to end the call, or replace handset to end call. TALK to end the call, or replace handset to end call Note: You can redial a number up to 32 digits RECEIVING A CALL: USING RECALL: Press the TALK button to answer Press the RECALL button IN USE will light up i) To access: · Call waiting · Conference calling · Other services provided by local company. ii) To instantly end a call and to regain a dial tone. TALK to end the call, or replace handset to end call. VT650 User Guide A/W 30/5/02 2:07 pm Page 15 14 Ringer & Receiver Volume & Ringer Tone Channel Selection & Speed Dialing 15 RECEIVER VOLUME CONTROL: Press RINGER button, during conversation NOTE: There are 8dB difference between receiver Hi/Lo. [. . . ] During pause press last message or PLAY to replay to replay all messages VT650 User Guide A/W 30/5/02 2:07 pm Page 27 26 Memo Functions 2-Way Recording & Answer Only 27 RECORDING A MEMO: Press MEMO button and hold until B E E P . 2-WAY RECORDING: Press 2-WAY REC. at any time during a call and hold untilL BEEP, BEEP, BEEP Display shows oo speak into MIC (you have 90 seconds to record) Press the STOP button to stop recording STOP to end recording ANSWER ONLY: To answer calls but not receive messages PLAYING A MEMO: Press the PLAY button and hold until all new messages are announced, followed by play of allL new messages and memos. press ANS. ON/OFF and hold until B E E P , OGM2 will be played OGM2 will play on answering call press ANS. ON/OFF and hold until B E E P , returns to normal mode VT650 will answer and play OGM1 and record incoming messages L Both sides of the conversation are recorded. The display shows 2 VT650 User Guide A/W 30/5/02 2:07 pm Page 29 28 Call Screening, Memory Full & Power Down Caller Breakthrough (CBT) 29 CALL SCREENING: You can monitor incoming messages by adjusting the volume control buttons VOL + CALLER BREAKTHROUGH (CBT): The CBT feature enables caller to alert you in an emergency. Default code = 0001 SETTING CBT CODE: VOL - Press the MEMORY FULL: i)Use When your VT650 memory is full, or has 60 messages in the memory it will revert to Answer Only mode NOTE: To prevent your VT650 memory becoming full you should delete your messages after you have listened to them or button and hold until asked for your CBT code to select first digit ii)Use ANS. ON/OFF to set first digit Repeat steps i) and ii) to select and set 2nd, 3rd and 4th digits. [. . . ]