User manual VTECH VT2961

[. . . ] PARTS CHECKLIST Handset Base Unit Wall Mounting Bracket AC power Adaptor Telephone Line Cords (x2) Short Telephone Line Cord 6. Belt Clip To purchase replacement battery packs, call VTECH Communications at 1-800595-9511. In Canada, call VTECH Electronics at 1-800-267-7377. CORDLESS DIGITAL VT 2961 900MHz MEMO ANSWER ON/OFF ANSWER 10:00 AM SIMON JAMES WILD 654532 465929115 NEW 00 LINE1 LINE2 TIME/SET SELECT MENU MENU CHARGING SPARE BATTERY DELETE NEW CALL LINE 1 OFF LINE 2 1 1 2 MAIL BOX PLAY/STOP SKIP 3 2 ABC 3 DEF 6 MNO 9WXYZ MUTE REPEAT 4 GHI 7PQRS TONE 5 JKL 8 TUV 0 OPER PROG VOLUME INTERCOM HOLD FLASH REDIAL/PAUSE CONF HOLD FLASH CONF INTERCOM WALL MOUNTING BRACKET MIC LINE 1 OFF LINE 2 HANDSET BASE UNIT (2-wire) (4-wire) AC POWER ADAPTOR TELEPHONE LINE CORDS BATTERY PACK SHORT TELEPHONE LINE CORD BELT-CLIP 1 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Follow all warnings and instructions marked on the product. [. . . ] Please call again. Thank you. " will be used. (see Recording the OGM) Example for OGM1 (for multi - user application): "Hi!We can't come to the phone right now. If you have a message for John press 1 ('Star 1'), for Jane press 2 ('Star 2'), for Jack press 3 ('Star 3'). Or, just stay on the line and record after the beep. Thank you. " Example for OGM2 (Announce Only): "Hi!Thank you. " 20 ANSWERING SYSTEM SETUP NOTE: Recording Your OGM MENU CORDLESS In Announce Only mode, your outgoing announcement is repeated before hanging up. DIGITAL VT 2961 900MHz MEMO ANSWER ON/OFF ANSWER MEMO TIME/SET SELECT MENU MENU CHARGING SPARE BATTERY DELETE NEW CALL Recording / Playing / Deleting the Outgoing Messages (OGM) 2 MAIL BOX PLAY/STOP 1 REPEAT 2 MAIL BOX PLAY/STOP SKIP 3 1 3 VOLUME MUTE INTERCOM 1. Press MENU key until the desired item (Set Outgoing Message) is announced. "Now recording", is announced, followed by a beep. Speak towards the front of the Answering System (max. length: 90 seconds). CONF HOLD FLASH LINE 1 OFF LINE 2 MIC 3. Press any MAILBOX key to stop the recording. Then OGM replays the message automatically, followed by a beep. To review a recorded announce-ment, press MENU key until "Set Outgoing Message" is announced. Press any MAILBOX key. The current greeting is played. To delete a recorded announce-ment, press DELETE during OGM playback. You then hear "Outgoing Message has been erased". NOTE: If your recording time is less than 2 seconds, your OGM will not be recorded, and the default greeting will be used. Set Security Code The security code programmed into the Answering System is used to gain access to functions from remote locations. The security code default setting is 19. Press MENU unit you hear "Set security code. " 2. Press TIME/SET to hear the current security code. Press SELECT briefly to increase the security code by 1. Or, hold SELECT continuously to increase the code by multiples of 10. Press TIME/SET to confirm your choice and you will hear the announcement of the security code. Set Security Code DIGITAL CORDLESS VT 2961 900MHz MEMO ANSWER ON/OFF ANSWER MENU TIME/SET SELECT MENU MENU CHARGING SPARE BATTERY DELETE NEW CALL TIME/SET 1 REPEAT 2 MAIL BOX PLAY/STOP SKIP 3 VOLUME SELECT MUTE INTERCOM CONF HOLD FLASH TIME/SET LINE 1 OFF LINE 2 MIC 21 ANSWERING SYSTEM SETUP Day and Time During initial setup, or after a power failure, the day and time default is set to Monday, 12:00am. [. . . ] Disconnect (remove) the handset battery pack. Remove the base unit battery pack, where applicable. Install the base unit battery pack, where applicable. Place the handset in the base unit cradle. [. . . ]