User manual WA KATES SOLVAIR MODEL SA385

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual WA KATES SOLVAIR MODEL SA385. We hope that this WA KATES SOLVAIR MODEL SA385 user guide will be useful to you.

Lastmanuals help download the user guide WA KATES SOLVAIR MODEL SA385.


Mode d'emploi WA KATES SOLVAIR MODEL SA385
Download
Manual abstract: user guide WA KATES SOLVAIR MODEL SA385

Detailed instructions for use are in the User's Guide.

[. . . ] « There are two inlets or supply connections; a low-pressure inlet on one side and a high-pressure inlet located directly opposite on the other side. The outlet of the Solvair is located on the same side as the high-pressure inlet. « It is crucial to the operation of the Solvair that the media coming in on the high-pressure inlet is at least 5 psi higher than the media coming in the low-pressure inlet. [. . . ] Then turn counter-clockwise and count 1-1/2 rotations from the closed position. This is a good starting point for most applications. « Turning the needle valves counter clockwise increases flow, clockwise will decrease flow. « As you make adjustments to increase or decrease flow, you should concentrate on keeping the number of turns of each valve within ¼ turn of each other. It is best to adjust them the same amount at the same time. If the needle valves are in dramatically different positions, the valve can get out of balance and perform erratically. As you approach the optimum settings, two phase flow will occur and small adjustments will make large changes in backpressure (outlet pressure) and overall flow. SERVICE INSTRUCTIONS · CAUTION: MAKE SURE THAT THE SOLVAIR IS RELIEVED OF PRESSURE BEFORE ATTEMPTING TO SERVICE OR CLEAN. At no time should the Solvair be disassembled while installed in the piping system. It is to be serviced at the factory or in a clean room environment by trained personnel. The Solvair is a finely tuned piece of instrumentation and should be treated with great care. Do not remove any of the snap rings while the Solvair is installed in the piping system. Damage to the unit or personal injury may result. To clean the unit, remove the unit from system and set up a clean area to work in. Remove retaining rings and pull endcaps off carefully. Be sure not to drop or damage the spool. [. . . ] KATES COMPANY will replace free of charge any equipment returned, with shipping charges prepaid, found to have been defective at time of shipment. This warranty does not apply to: (a) damage resulting from misuse or inadequate handling; (b) damage resulting from continued use after defect is apparent; (c) any other damage, loss or liability; or (d) any piece of equipment that is changed, modified or altered in any way after it leaves the factory. The liability of the PRECISE FINISHING SYSTEMS COMPANY shall be limited to the replacement, f. o. b. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WA KATES SOLVAIR MODEL SA385

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual WA KATES SOLVAIR MODEL SA385 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag