User manual WAGNER CONTROL SPRAY

[. . . ] Owner's manual: Read this manual for complete instructions Manual del propietario: Le este manual para obtener instrucciones completas English - Table of Contents Safety Information . 16 Technical service hours: Monday through Friday, 8:00 am to 4:30 Central Time Español - Tabla de Contenido Información de seguridad . . 16 1-800-328-8251 Wagner Technical Service Or visit us on the world wide web!¡O visitenos en Internet! http://www. wagnerspraytech. com Horario del servicio técnico: De lunes a viernes, de 8 a. m. [. . . ] DANGER--Improper installation of the grounding plug can result in a risk of electric shock. If repair or replacement of the cord or plug is necessary, do not connect the green grounding wire to either flat blade terminal. The wire with insulation having a green outer surface with or without yellow stripes is the grounding wire and must be connected to the grounding pin. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if you are in doubt as to whether the product is properly grounded. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. This product is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated below. Make sure that the product is connected to an outlet having the same configuration as the plug. Grounding Instructions This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. Grounded Outlet Grounding Pin Cover for grounded outlet box Components Filter housing Air cap Nut Nozzle Seal Trigger Material adjustment knob Turbine Fluid container Handle Viscosity cup 3 English Setup Assembly 1. Align the arrow on the spray gun with the "unlock" symbol on the turbine. Insert and twist the spray gun into the turbine toward the "lock" symbol on the turbine. The tab below the trigger will lock the two pieces into place. Material Preparation Before spraying, the material being used may need to be thinned with the proper solvent as specified by the material manufacturer. Never exceed the thinning advice given by the coating manufacturer. Do not use materials with a flashpoint below 70°F (21°C). Stir the spraying material thoroughly before measuring viscosity. Dip the viscosity test cup completely into the spraying material. Aligning the Suction Tube If you are going to be spraying in a downward direction, the angled end of the suction tube should be pointing toward the front of the gun. Hold the test cup up and measure the time in seconds until the liquid empties out. This time is referred to below as Runout Time. Material 1) Oil enamel 2) Oil based primer 3) Oil stain 4) Clear sealer 5) Polyurethane 6) Varnish Thinning Chart Runout Time 25-40 30-45 No thinning required No thinning required No thinning required 20-50 Material to be sprayed should always be strained to remove any impurities in the paint which may enter and clog the system. Impurities in the paint will give poor performance and a poor finish. MATERIAL FLASH POINT MUST BE 70°F (21°C) OR HIGHER. If you are going to be spraying in an upward direction, the angled end of the suction tube should be pointing toward the rear of the gun. Fill Container 1. After the material has been properly thinned and strained, fill the container to the top of the neck. By pointing the suction tube in the proper direction, you will not have to refill the container as often. 3. [. . . ] This warranty does not cover damage resulting from improper use, accidents, user's negligence or normal wear. This warranty does not cover any defects or damages caused by service or repair performed by anyone other than a Wagner Authorized Service Center. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO ONE YEAR FOLLOWING DATE OF PURCHASE. WAGNER SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR BREACH OF THIS WARRANTY OR ANY OTHER REASON. [. . . ]