User manual WEIDER 831.159710

[. . . ] 831. 159710 Serial No. (Write the serial number in the space above for reference. ) USER'S MANUAL Serial Number Decal (under seat) SEARS, ROEBUCK AND CO. HOFFMAN ESTATES, IL 60179 CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Visit our website at www. weiderfitness. com new products, prizes, fitness tips, and much more! TABLE OF CONTENTS FULL 90-DAY WARRANTY . . Back Cover Note: A PART IDENTIFICATION CHART is attached in the center of this manual. [. . . ] IMPORTANT: While assembling the cables, do not overtighten the bolts and nuts securing the pulleys. The pulleys must turn freely. 8 23 58 9. Route the Long Cable around a 3 1/2" Pulley (15). Using a 3/8" x 3 1/2" Bolt (16) and a 3/8" Nylon Jamnut (25), attach the 3 1/2" Pulley (15) in the indicated location on the Top Frame (55). Be sure that the end of the Cable with the ball is on the indicated side of the Pulley and that the Cable is between the Pulley and the hook on the Top Frame (55). 9 25 15 55 58 CABLE ASSEMBLY Ball Hook 16 10. Wrap the Long Cable (58) around a "V"-Pulley (6). Using a 3/8" x 1 3/4" Bolt (71) and a 3/8" Nylon Locknut (21), secure the Pulley to the indicated bracket on the Top Frame (55). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. 15 15 71 55 58 Bracket 21 9 16. Attach the Long Cable (58) to the Weight Carriage (19) with a 3/8" x 3/4" Bolt (69) and a 3/8" Nylon Locknut (21). Make sure that the Bolt and the Nylon Locknut are tight. 16 58 21 19 69 CABLE ASSEMBLY 17. Using a 3/8" x 3 1/2" Bolt (16), a 3/8" Flat 17 Washer (9), and a 3/8" Nylon Locknut (21), secure a 3 1/2" Pulley (15) and a Cable Trap (66) to the upper hole in the Press Frame (17). Make sure that the Cable Trap and the Pulley are oriented as shown. Hold a 3 1/2" Pulley (15) inside the indicated bracket on the Press Frame (17). Using a 3/8" x 8" Bolt (59), two 3/8" Flat Washers (9), and a 3/8" Nylon Locknut, attach the 3 1/2" Pulley to the Press Frame as shown. 15 66 16 59 9 15 21 9 17 Bracket 18. Route the Short Cable under the indicated 3 1/2" Pulley (15). Be sure that the end of the Cable with the ball is between the Pulley and the crossbar on the Press Frame (17). 18 17 15 Ball Crossbar 23 10 19. Slide a Cable Trap (66) and a 3 1/2" Pulley (15) onto each 3/8" x 3 3/4" Bolt (68). Insert the Bolts into the Front Upright (42) from the direction shown. Hand tighten a 3/8" Nylon Locknut (21) with a 3/8" Flat Washer (9) onto each Bolt. Be sure that all parts are oriented as shown. Do not tighten the Nylon Locknuts yet. 19 42 15 9 66 68 15 21 20. [. . . ] Re-attach the Pulley and the Cable Trap to the other hole in the "U"-Bracket. Make sure that the Cable Trap is in the proper position and that the Cable and Pulley move smoothly. Note: If a cable tends to slip off the pulleys, the cable may have become twisted. If a cable needs to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual. 66 15 57 12 21 2 23 18 CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (23) and the Long Cable (58). [. . . ]