User manual WEIDER WESY96350

[. . . ] Remove the PART IDENTIFICATION CHART before beginning assembly. FULL 90 DAY WARRANTY For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this SEARS WEIGHT SYSTEM EXERCISER, contact the nearest SEARS Service Center throughout the United States and SEARS will repair or replace the WEIGHT SYSTEM EXERCISER, free of charge. This warranty does not apply when the WEIGHT SYSTEM EXERCISER is used commercially or for rental purposes. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 817WA, HOFFMAN ESTATES, IL 60179 2 IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the home gym. [. . . ] Lubricate both axles on the Top Frame (55). Slide the Right Arm (48) onto the right axle. Note: Be careful not to confuse the Right Arm with the Left Arm (47); refer to step 6 to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the Top Frame (55). Tap two 1" Retainers (63) and a 1" Round Cover Cap (62) onto the right axle. Be sure that the teeth on the Retainers bend toward the Cover Cap, as shown in the inset drawing. Attach the Left Arm (47) in the same manner. Press 1 3/4" Square Inner Caps (44) into the lower ends of the Right and Left Arms (47, 48). Wet the lower end of each Arm with soapy water. Slide a Foam Pad (45) onto the lower end of each Arm. 7 55 47 Bracket Lubricate Axle 48 63 62 45 44 45 55 63 62 7 8. During steps 9 through 22, refer to the CABLE DIAGRAM on page 19 of this manual to verify proper cable routing. Route the Long Cable (58) around the Pulley and through the Long "U"-Bracket. Be sure that the Cable is in the groove of the Pulley, that the Cable Trap is turned to hold the Cable in place, and that the Cable and Pulley move smoothly. 13 66 20 15 58 12 CABLE ASSEMBLY 55 64 20 3 14 66 15 58 57 15. Route the Short Cable (23) up around the 3 1/2" Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Next, route the Short Cable (23) around the 3 1/2" Pulley (15) attached to the upper hole in the Front Upright (42). Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley (15) as shown. 21 42 15 66 42 23 Inset shows view from other side 23 15 15 66 21 17 11 22. Attach the end of the Short Cable (23) to the Long "U"-Bracket (57) with a 1/4" Nylon Locknut (2) and a 1/4" Flat Washer (10). Do not completely tighten the Nylon Locknut; it should be threaded onto the end of the Cable until two threads are showing above the Nylon Locknut, as shown in the inset drawing. 22 2 CABLE ASSEMBLY 57 10 23 2 10 57 23. Attach the Backrest (41) to the Front Upright (42) with two 1/4" x 2 1/2" Screws (43) and two 1/4" Flat Washers (10). 23 23 42 SEAT ASSEMBLY 41 43 10 12 24. Press a 1 1/2" Square Inner Cap (32) into the Seat Frame (36). [. . . ] If there is slack in the cables before resistance is felt, the cables should be tightened. Slack can be removed from the Short Cable (23) by by tightening the 1/4" Nylon Locknut (2) at the end of the Cable. Additional slack can be removed by moving the 3 1/2" Pulley (15) to the other hole in the Long "U"-Bracket (57). Remove the 3/8" Nylon Locknut (21) and the 3/8" x 2" Bolt (12) from the Cable Trap (66), the Pulley, and the "U"-Bracket. [. . . ]