User manual WELLTECH FXO GATEWAY H.323 3804

[. . . ] FXO GATEWAY User Manual (3802/04/06) STEPS IN CONFIGURATION 1. START UP 1. 1 Introduction 1. 2 Features and specification 1. 3 Accessories and equipment 1. 4 Appearance 1. 4. 1 3802 1. 4. 2 3804 1. 4. 3 3806 2. HOW TO SETUP AND CONNECT BASICALLY 2. 1 System Requirement 2. 2 IP Environment Setting 2. 2. 1 For Windows 2000/NT 2. 3 Network configurations in your gateway 2. 3. 1 Static ip address 2. 3. 2 DHCP mode 2. 3. 3 PPPoE mode 2. 4 Making a VoIP Call 2. 4. 1 Configure the gateway into the Peer-to-Peer mode 2. 4. 2 Configure the gateway into the GK routed mode 2. 4. 2. 1 The type in GK routed mode 3. COMMAND LIST 3. 1 Hyper Terminal Setting 3. 2 Command List 3. 2. 1 [help] command 3. 2. 2 [quit] command 3. 2. 3 [debug] command 3. 2. 4 [reboot] command 2 3 3 3 4 5 5 6 7 9 9 10 10 12 14 16 17 18 19 21 22 24 24 27 27 27 28 28 FXSO H. 323 Gateway User Manual Document Ver. : 177A Release OCT. , 2003 3. 2. 5 [flash] command 3. 2. 6 [commit] command 3. 2. 7 [ifaddr] command 3. 2. 8 [time] command 3. 2. 9 [ping] command 3. 2. 10 [greetrd] command 3. 2. 11 [pbook] command 3. 2. 12 [pppoe] 3. 2. 13 [ddns] command 3. 2. 14 [sysconf] command 3. 2. 15 [h323] command 3. 2. 16 [voice] command 3. 2. 17 [tos] command 3. 2. 18 [tone] command 3. 2. 19 [support] command 3. 2. 20 [group] command 3. 2. 21 [bureau] command 3. 2. 22 [prefix] command 3. 2. 23 [rom] command 3. 2. 24 [passwd] command 29 29 30 32 32 33 35 38 38 40 44 46 48 49 50 51 53 54 55 57 1 FXSO H. 323 Gateway User Manual Document Ver. : 177A Release OCT. , 2003 Steps in configuration STEP 1 Start Up To check out the peripheral equipments and understand the feature of this gateway. [. . . ] (2) If called party is FXS product, please set e164 of pbook as prefix of called party, when dialing to different line of FXS product, please dial line number. 3. 2. 12 [pppoe] Display PPPoE related information. --------------------------------------------------------------------------------------------------PPPoE device information and configuration Usage: pppoe [-print]|[-open]|[-close] pppoe [-dev on/off][-id username][-pwd password] -print Display PPPoE device information. -reboot Reboot after remote host disconnection. --------------------------------------------------------------------------------------------------Paremeter Usage: -print print PPPoE status. -dev Enable PPPoE Dial-up function -open Open the connection -close Close the connection -id Input the User name ID provided by ISP -pwd Input the User name password provided by ISP -reboot Reboot the PPPoE connection. 3. 2. 13 [ddns] command Support the DDNS function ------------------------------------------------------------------------------------------------- 38 FXSO H. 323 Gateway User Manual Document Ver. : 177A Release OCT. , 2003 Parameter Usages: -enable enable the DDNS function -server enter the server address of the DDNS server you use -hostname enter the domain name address which you get from the DDNS server -id key in your id -passwd key in your password -checkIP enable or disable the check current user's IP address 39 FXSO H. 323 Gateway User Manual Document Ver. : 177A Release OCT. , 2003 -checkIPsrv1 enter the IP address of the check server -checkIPsrv2 the secondary IP address of the check server -delay service delay time -force execute the DDNS function all the times Note: Support DDNS Server: www. 3322. org, www. dyndns. org. 3. 2. 14 [sysconf] command This command displays the system information and configuration. ------------------------------------------------------------------------------------------------- 40 FXSO H. 323 Gateway User Manual Document Ver. : 177A Release OCT. , 2003 - service: 0 Dial In Service in Dial In Service, WellGate FXO GateWay will pick up incoming calls from PSTN, 41 FXSO H. 323 Gateway User Manual Document Ver. : 177A Release OCT. , 2003 play pre-recorded voice greeting or, and then have users to make a 2nd dial to destination. 1/2 HotLine Service (this feature must be implemented after set bureau ­table command) HotLine Service provides Hot Line function, which connects directly to pre-defined destination. For ex: if L1 of WellGate FXO GateWay is assigned to destination address 192. 168. 1. 12 in Hot Line Mode. When users from PSTN make a call to L1 of WellGate FXO GateWay, it will directly connect to 192. 168. 1. 12 without a 2nd dial. 3 The connect signal will sent to IP side if gateway detect the reverse signal. It is using the billing application. - ringdet: to define ring detection method. (0 is for old hardware version; 1 for new hardware version) - plan: It is for setting dial-numbering plan. While e164 number is three digits, the plan should be set as 3 or 0. The plan 0 is for any positive digits use. - port: This command can enable or disable individual port. The default value is set to enable all ports. - idto: The duration of two pressed digits in dial mode -eod: Digit type of end of dialing. ( 0:No end of dialing, 1:[*] button, 2:[#]button ) - seizure: line seizure mode. None (0) when calling from IP side, choose L1 every time if it is available. UCD (1) when calls from IP side, choose L1 for the first time, and L2 for the 2nd time, (cyclic) Note: Do not enable this function together with group (please refer to 5. 18). - 2nddial: This command is necessary for setting one time dial method use. While user would like to skip 2nddial process, WellGate FXO GateWay must close 2nddial and set as 0 (2nddial off). The default value is set as 1 (2nddial on). [. . . ] They have to use the following command: ------------------------------------------------------------------------------------------------- 3. 2. 21 [bureau] command Type bureau to display the command usage. ------------------------------------------------------------------------------------------------- 53 FXSO H. 323 Gateway User Manual Document Ver. : 177A Release OCT. , 2003 Parameter Usages: - print: display bureau line information and configuration. ------------------------------------------------------------------------------------------------- - pstn: PSTN number (per port basis). This number is used to display as a caller ID when the caller ID is not available. [. . . ]