User manual WENGER WATCH

[. . . ] Water-Resistant ­ To 50m (165') or 100m (330') for standard watches. To 200m (660') or 1000m (3300') for dive watches. Straps/Bracelets ­ Stainless steel and titanium bracelets feature dive buckles or deployant jewelry buckles. Straps are offered in genuine calfskin leather, specially treated rubberized leather, water-resistant rubber or nylon, or other high-quality materials. [. . . ] *please use a blunt object, such as a pen tip, to operate the inset pushers. 11 Right inset pusher* 2nd Time Zone Dual Sub-Dial Watch Bracelet or strap Hour hand 60 Setting the Time and Date of 2nd Time Zone Dual Sub-Dial Watches Setting the Primary Date and Time (Large minute and hour hands) See pages 6-7 for complete instructions. Minute hand 55 05 Setting the 2nd Time Zone 1. Depress the 2nd time zone pusher for at least 2 seconds and release. The minute hand will automatically advance one minute. 9 10 2nd Time zone minute hand 45 50 11 12 9 6 3 1 10 60 45 15 30 Crown 15 2 2. Depress the pusher again and hold it down to advance the minute and hour hands. The longer the pusher is depressed, the faster the time will advance. If you do not depress the pusher for 10 seconds your watch will automatically exit the setting mode. 34 8 20 40 07 30 Date 12 25 35 2nd Time zone hour hand 5 7 Second hand 2nd Time zone pusher 13 Operating Instructions For Flip-Open Compass Watch Note: For watches featuring a swing-out compass watch, see page 16. Your Wenger Swiss G3 Navigator Compass watch has two crown components (illustration below) and four crown positions (right): Component 1 ­ Inner security-screw crown used to lock down or open the case to reveal the compass. Component 2 ­ Outer crown used to adjust time and date. Inner security-screw crown need not be unscrewed to set time and date. Position 1 Position 2 Position 3 Position 4 Position 3 ­ Outer crown extended one "click" out for use in setting the date. Position 4 ­ Outer crown extended two "clicks" out for use in setting the time. Setting the Date and Time 1. Set the crown of the watch to Position 3 (pull outer crown one "click" out). Turn the crown counter-clockwise until the date shows one day earlier than the date you want to set. Pull out the crown to Position 4 (two "clicks" out). Turn the crown counterclockwise so the watch hands move clockwise until the current date shows. (continued on next page) 15 Position 1 ­ Both components fully depressed and screwed down for general use and wear. Position 2 ­ Inner crown unscrewed to flip open the dial and reveal the compass. 14 Then set the watch hands to the correct time. Turn the watch hands past 12 once if you're setting the watch for a P. M. Push the outer crown back in to Position 1. 1 2, 3 4 5, 6 Setting the Time Only Pull out the outer crown to Position 4 (two "clicks" out) and set the time by turning the crown clockwise or counter-clockwise. Note: In order to ensure that your watch remains water-resistant, it is important that you make certain the crown is always returned to Position 1. Lay the open watch on a flat surface, ensuring that the open case is at a 90 degree angle in relation to the compass, so that the compass is flat. Your compass will adjust to accurately reflect orientation within 30 seconds; the arrow may undergo some movement during this period. [. . . ] If your warranty has been rendered void as a result of non-compliance with above warranty restrictions, we will send you an estimate before any repairs are made. When sending your watch to our Service Center, please pack it securely. We suggest insuring the shipment as Wenger NA cannot be responsible for packages not received by the company. Be sure to include your name, mailing address, phone number, email address, proof of purchase and a brief description of the problem. [. . . ]