User manual WESLO CADENCE G-40

[. . . ] Write the serial number in the space above for future reference. Serial Number Decal USER'S MANUAL QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if parts are damaged or missing, PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT DIRECTLY. CALL TOLL-FREE: 1-888-936-4266 Mon. ­Fri. , 8:00 until 17:00 EST (excluding holidays) OR E-MAIL US: customerservice@iconcanada. ca CAUTION Read all precautions and instructions in this manual before using Visit this equipment. [. . . ] To reset the displays, press the Stop button, remove the key, and then reinsert the key. 14 Note: The console can display speed and distance in either miles or kilometers. To see which unit of measurement is selected, first remove the key from the console. Next, hold down the Stop button, reinsert the key, wait until you hear a tone, and then release the Stop button. An "E" for English miles or an "M" for metric kilometers will appear in the upper display. Press the Speed + button to change the unit of measurement if desired. When the desired unit of measurement is selected, remove the key and then reinsert it. To measure your heart rate, stand on the foot rails and place your thumb on the pulse sensor (see the drawing on page 13). Do not press too hard, or the circulation in your thumb will be restricted and your pulse may not be detected. When your pulse is detected, the small heart symbol in the lower right display will flash, one or two dashes will appear, and then your heart rate will be shown. For the most accurate heart rate reading, hold your thumb on the pulse sensor for at least 15 seconds. If the displayed heart rate appears to be too high or too low, or if your heart rate is not displayed, lift your thumb for a few seconds, and then reposition your thumb on the pulse sensor. Remember to stand still while measuring your heart rate. When you are finished exercising, remove the key from the console. Step onto the foot rails, press the Stop button, and adjust the incline of the treadmill to the lowest setting. The incline must be at the lowest setting or you may damage the treadmill when you fold it to the storage position. Next, remove the key from the console and put it in a secure place. When you are finished using the treadmill, switch the reset/off circuit breaker to the "off" position and unplug the power cord. IMPORTANT: If you do not do this, the treadmill's electrical components may wear prematurely. HOW TO USE A SPEED PROGRAM 1. See HOW TO TURN ON THE POWER on page 13. To select a speed program, press the Program Select button repeatedly; "P- 1, " "P- 2, " "P- 3, " or "P- 4" will appear in the upper display for a few seconds to show which program is selected. The maximum speed setting of the selected program will also flash in one of the displays for a few seconds. Each program consists of 30 one-minute segments. [. . . ] WCTL29607. 0 24 21 42 60 36 29 74 82 94 40 95 R0807A EXPLODED DRAWING B--Model No. WCTL29607. 0 20 20 20 R0807A 47 47 47 65 98 30 34 38 44 38 59 34 21 42 42 21 21 21 79 57 87 66 37 90 21 99 81 92 49 25 EXPLODED DRAWING C--Model No. WCTL29607. 0 77 77 88 R0807A 10 10 10 33 10 7 85 10 100 5 100 10 10 8 5 77 8 5 7 85 100 10 39 22 77 8 5 80 4 8 48 24 58 54 53 1 9 14 11 52 13 32 43 43 35 63 69 70 69 32 43 16 69 70 69 43 35 2 45 63 26 63 26 45 16 63 26 26 13 32 2 63 26 39 63 26 11 9 23 14 1 26 EXPLODED DRAWING D--Model No. WCTL29607. 0 R0807A 91 15 4 4 12 4 4 4 4 4 73 4 4 4 27 ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual. [. . . ]