User manual WESTINGHOUSE LCM-17V2

[. . . ] 7 OSD MENUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DIRECT CONTROL ­ KEYPAD BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 DISPLAY MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 AUTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The cord should never be severely bent, pinched, or twisted. Periodically inspect power cords for wear or damage, particularly near plug and the point where it exits from the product. Unplug cord and discontinue use if damage is discovered. Ventilation Slots and openings on the cabinet are provided for ventilation purposes. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. Keep LCD Monitor a minimum of four (4) inches away from any wall to assure sufficient airflow and ventilation. Increased temperatures may cause fire or device failure. 2 To assure proper ventilation, do not block the openings by placing the product on a bed, sofa, rug or other similar surface. Do not place the product in a built-in installation, such as a bookcase or enclosed rack, unless proper ventilation is provided. Other Notices and Precautions Caution: Never remove the rear cover. There are no user serviceable parts inside. Your LCD display contains high-voltage parts. You may be seriously injured if you touch them. Your warranty does not cover repairs or attempted repairs by anyone not authorized by manufacturer. Refer all servicing and repairs to qualified service personnel. If smoke, abnormal noise, or strange odor is present, immediately unplug the power cord. Contact a qualified service technician If your LCD Monitor will not be used for extended periods of time, unplug the power cord. 3 Cleaning the LCD Display · · MAKE SURE THE LCD DISPLAY IS TURNED OFF NEVER SPRAY OR POUR LIQUID DIRECTLY ONTO THE SCREEN OR CASE 1. Wipe the screen with a clean, soft, lint-free cloth. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen. To clean the screen: To clean the case: 1. If still not clean, apply a small amount of non-ammonia, non-alcohol based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface. Disclaimer Manufacturer does not recommend the use of any ammonia or alcohol-based cleaners on the LCD display screen or case. Some chemical cleaners have been reported to damage the screen and/or LCD display case. Manufacturer will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners. 4 Safety Guidelines Warning: This device must be operated with the original power supply, part number: ADP-60CF A. CAUTION: The socket-outlet should be installed near the equipment and should be easily accessible. [. . . ] These modes automatically change the backlighting levels between bright, brighter and brightest. Auto Pressing the AUTO button on the control keys will adjust automatically the picture and synch the LCD Monitor. The LCD monitor will start the Auto Adjust process automatically and run for approximately 10 seconds, during which time you will notice the image changing and re-synching. 9 Image not Displayed Input Source Not Found If there is no source connected to the Input selected. Out of Range If the Display settings is not compatible or out of range of the LCD Monitor the following will be displayed: 10 Appendix Specifications Panel Optimum Resolution Response Time Contrast Ratio Maximum Brightness Viewing Angles Color Saturation Wall/Arm Mount Input Signal Physical Video Audio Speaker Output Power Operating Conditions Voltage Temperature Humidity Altitude Storage Conditions Temperature Humidity Altitude Dimensions Physical Type 17" Color TFT LCD 1280 x 1024 14 ms 350:1 350 Nits 160° (H) / 140° (V) 72% TBD 75mm VESA® HD-15 pin mini D-Sub (VGA connector) 3. 5mm Mini-Stereo jack male-male Built-in audio amplifier and speakers, 2. 5 watts * 2 channels 100-240 VAC, 50/60 Hz (auto switch), 1. 5A 32° F to +95° F (0° C to +35° C) 20% to 90% (no condensation) To 3, 000 Meter -4° F to + 140° F (-20° C to + 60° C) 10% to 90% (no condensation) To 12, 000 Meter 15. 1 (w) x 16. 2 (h) x 8. 3 (d) in 17. 5 (w) x 18. 2 (h) x 5. 1 (d) in Weight Regulations Power consumption DC on DC Off Lamp Life Net 7. 7 lb (2. 8 kg) FCC-B, UL, CSA (CUL), Energy Star®, Plug & Play <73W <3W (Blue LED) (LED OFF) 40, 000 hours 11 Troubleshooting No power · · · Make sure DC cord is plugged into the back of the LCD Monitor. Make sure AC power cord is securely connected to the AC socket Plug another electrical device (like a radio) to the power outlet to verify that the outlet is supplying the proper voltage No Image · · Make sure power button is ON. Check whether the LCD monitor and computer power cords are plugged in and whether there is a supply of power. Power is ON but no screen image · · · Adjust brightness and contrast Check signal connection properly seated both on PC and Monitor. "Out Of Range" Check the computer image output resolution and frequency and compare the value with the preset values of graphics card. Fuzzy Image · · · · · Adjust Phase. Image to Bright or to Dark Adjust brightness and contrast by OSD. Irregular Image Check the signal connection between the computer and LCD monitor. [. . . ]